AT49BV4096A-15RI Atmel, AT49BV4096A-15RI Datasheet
AT49BV4096A-15RI
Specifications of AT49BV4096A-15RI
Related parts for AT49BV4096A-15RI
AT49BV4096A-15RI Summary of contents
Page 1
... The input has no effect on the operation of the device. I/O0 - I/O15 Data Inputs/Outputs I/O15(A-1) I/O15 (Data Input/Output, Word Mode) A-1 (LSB Address Input, Byte Mode) BYTE Selects Byte or Word Mode NC No Connect 4-megabit (512K x 8/ 256K x 16) Single 2.7-volt ™ Battery-Voltage Flash Memory AT49BV4096A AT49LV4096A Rev. 1618F–FLASH–11/02 1 ...
Page 2
AT49BV/LV4096A SOIC (SOP) VPP A17 GND ...
Page 3
... X DECODER READ: The AT49BV/LV4096A is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high-impedance state whenever high. This dual-line control gives designers flexibility in preventing bus contention ...
Page 4
... Block Programming Lockout Override” section). ERASURE: Before a byte or word can be reprogrammed, it must be erased. The erased state of memory bits is a logic “1”. The entire device can be erased by using the Chip Erase command or individual sectors can be erased by using the Sector Erase commands ...
Page 5
... TTL levels, the boot block programming lockout feature is again active. PRODUCT IDENTIFICATION: The product identification mode identifies the device and manufacturer as Atmel. It may be accessed by hardware or software operation. The hardware operation mode can be used by an external programmer to identify the correct programming algorithm for the Atmel product. For details, see “ ...
Page 6
... Either one of the Product ID Exit commands can be used sector addresses: (A17 - A0 01XXX for BOOT BLOCK SA = 02XXX for PARAMETER BLOCK 03XXX for PARAMETER BLOCK 3FXXX for MAIN MEMORY ARRAY Absolute Maximum Ratings* Temperature under Bias ................................ -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C All Input Voltages (including NC Pins) with Respect to Ground ...
Page 7
... Condition MHz OUT -400 µA OH AT49BV/LV4096A AT49BV4096A-90 0°C - 70°C N/A 2.7V - 3. OUT High-Z High-Z X High-Z ( A17 = Manufacturer Code ( A17 = Device Code A17 = V Manufacturer Code A17 = V Device Code IH IL Min Max 10.0 10.0 50.0 0.5 25.0 0.6 2.0 ...
Page 8
... RO RESET HIGH Z OUTPUT OUTPUT - t after the address transition without impact on t ACC after the falling edge of CE without impact pF). L 2.4V 0. < 3.3V 1.8K OUTPUT PIN 1.3K 100 pF AT49BV4096A-90 Max Min Max 800 800 VALID . ACC after an address change CE ACC ...
Page 9
Pin Capacitance MHz ° C (1) Symbol Typ OUT Note: 1. This parameter is characterized and is not 100% tested. AC Word Load Characteristics Symbol Parameter ...
Page 10
Program Cycle Characteristics Symbol Parameter t Byte/Word Programming Time BP t Address Setup Time AS t Address Hold Time AH t Data Setup Time DS t Data Hold Time DH t Write Pulse Width WP t Write Pulse Width High ...
Page 11
Data Polling Characteristics Symbol Parameter t Data Hold Time Hold Time OEH ( Output Delay OE t Write Recovery Time WR Notes: 1. These parameters are characterized and not 100% tested. 2. See t ...
Page 12
Software Product Identification Entry LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 90 TO ADDRESS 5555 ENTER PRODUCT IDENTIFICATION (2)(3)(5) MODE Software Product Identification Exit OR LOAD DATA AA TO ADDRESS 5555 LOAD DATA ...
Page 13
... Notes: 1. The topside marking will be AT49LV4096A1. 2. The topside marking will be AT49LV4096A5. 3. The topside marking will be AT49BV4096A1. 4. The topside marking will be AT49BV4096A5. 48C1 48-ball mm, Chip-size Ball Grid Array Package (CBGA) 48C5 48-ball mm, Chip-size Ball Grid Array Package (CBGA) 44R 44-lead, 0.525" Wide, Plastic Gull Wing Small Outline (SOIC) ...
Page 14
Packaging Information 48C1 – CBGA Dimensions in Millimeters and (Inches). Controlling dimension: millimeters. 0.875 (0.034) REF 0.75 (0.0295) BSC NON-ACCUMULATIVE 2325 Orchard Parkway San Jose, CA 95131 R AT49BV/LV4096A 14 7.10(0.280) 6.90(0.272 7.10(0.280) 6.90(0.272) TOP VIEW 5.25 (0.207) ...
Page 15
CBGA Dimensions in Millimeters and (Inches). Controlling dimension: millimeters. 0.80 (0.0315) BSC NON-ACCUMULATIVE 2325 Orchard Parkway San Jose, CA 95131 R 1618F–FLASH–11/02 6.10 (0.240) 5.90 (0.232 8.10 (0.319) 7.90 (0.311) TOP VIEW 1.00(0.039) REF 4.00(0.157) 6 ...
Page 16
SOIC Dimensions in Millimeters and (Inches). Controlling dimension: Inches. 2325 Orchard Parkway San Jose, CA 95131 R AT49BV/LV4096A 16 0.508(0.020) 0.356(0.014) 13.46(0.530) 13.21(0.520) PIN 1 1.27(0.050) BSC 28.32(1.115) 28.07(1.105) 0.33(0.130) 1.27(0.050) 0º ~ 8º 1.00(0.039) 0.60(0.024) TITLE 44R, ...
Page 17
TSOP Pin 1 Identifier e E Notes: 1. This package conforms to JEDEC reference MO-142, Variation DD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and on ...
Page 18
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...