MT48H8M32LFB5-8 IT TR Micron Technology Inc, MT48H8M32LFB5-8 IT TR Datasheet - Page 19
![IC SDRAM 256MBIT 8NS 90VFBGA](/photos/7/23/72313/mfg557-90-vfbga_sml.jpg)
MT48H8M32LFB5-8 IT TR
Manufacturer Part Number
MT48H8M32LFB5-8 IT TR
Description
IC SDRAM 256MBIT 8NS 90VFBGA
Manufacturer
Micron Technology Inc
Datasheet
1.MT48V8M32LFB5-8_IT_TR.pdf
(75 pages)
Specifications of MT48H8M32LFB5-8 IT TR
Format - Memory
RAM
Memory Type
SDRAM
Memory Size
256M (8Mx32)
Speed
8ns
Interface
Parallel
Voltage - Supply
1.7 V ~ 1.95 V
Operating Temperature
-40°C ~ 85°C
Package / Case
90-VFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
557-1053-1
MT48H8M32LFB5-8 IT
MT48H8M32LFB5-8 IT
BURST TERMINATE
AUTO REFRESH
SELF REFRESH
PDF: 09005aef80d460f2/Source: 09005aef80cd8d41
256Mb SDRAM x32_2.fm - Rev. G 6/05
mand is automatically performed upon completion of the READ or WRITE burst, except
in the full-page burst mode, where auto precharge does not apply. Auto precharge is non
persistent in that it is either enabled or disabled for each individual READ or WRITE
command.
Auto precharge ensures that the precharge is initiated at the earliest valid stage within a
burst. The user must not issue another command to the same bank until the precharge
time (
issued at the earliest possible time, as described for each burst type in "Operation" on
page 21.
The BURST TERMINATE command is used to truncate either fixed-length or full-page
bursts. The most recently registered READ or WRITE command prior to the BURST TER-
MINATE command will be truncated, as shown in "Operation" on page 21.
AUTO REFRESH is used during normal operation of the SDRAM and is analogous to
CAS#-BEFORE-RAS# (CBR) refresh in conventional DRAMs. This command is non per-
sistent, so it must be issued each time a refresh is required. All active banks must be
PRECHARGED prior to issuing an AUTO REFRESH command. The AUTO REFRESH
command should not be issued until the minimum
CHARGE command, as shown in "Operation" on page 21.
The addressing is generated by the internal refresh controller. This makes the address
bits “Don’t Care” during an AUTO REFRESH command. The 256Mb SDRAM requires
4,096 AUTO REFRESH cycles every 64ms (
REFRESH command every 15.625µs will meet the refresh requirement and ensure that
each row is refreshed. Alternatively, 4,096 AUTO REFRESH commands can be issued in a
burst at the minimum cycle rate (
The SELF REFRESH command can be used to retain data in the SDRAM, even if the rest
of the system is powered down. When in the self refresh mode, the SDRAM retains data
without external clocking. The SELF REFRESH command is initiated like an AUTO
REFRESH command, except CKE is disabled (LOW). Once the SELF REFRESH command
is registered, all the inputs to the SDRAM become “Don’t Care” with the exception of
CKE, which must remain LOW.
Once self refresh mode is engaged, the SDRAM provides its own internal clocking, caus-
ing it to perform its own auto refresh cycles. The SDRAM must remain in self refresh
mode for a minimum period equal to
indefinite period beyond that.
The procedure for exiting self refresh requires a sequence of commands. First, CLK must
be stable (stable clock is defined as a signal cycling within timing constraints specified
for the clock ball) prior to CKE going back HIGH. Once CKE is HIGH, the SDRAM must
have NOP commands issued (a minimum of two clocks) for
required for the completion of any internal refresh in progress.
Upon exiting the self refresh mode, AUTO REFRESH commands must be issued every
15.625µs or less as both SELF REFRESH and AUTO REFRESH utilize the row refresh
counter.
t
RP) is completed. This is determined as if an explicit PRECHARGE command was
19
t
RFC), once every 64ms.
t
RAS and may remain in self refresh mode for an
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
REF). Providing a distributed AUTO
t
RP has been met after the PRE-
256Mb: x32 Mobile SDRAM
t
XSR because time is
©2003 Micron Technology, Inc. All rights reserved.
Commands