AT17C002A-10JI Atmel, AT17C002A-10JI Datasheet
AT17C002A-10JI
Specifications of AT17C002A-10JI
Related parts for AT17C002A-10JI
AT17C002A-10JI Summary of contents
Page 1
... Replacement for AT17C/LV002A Description The AT17C002A and AT17LV002A (high-density AT17A Series) FPGA Configuration EEPROMs (configurators) provide an easy-to-use, cost-effective configuration mem- ory for programming Altera FLEX devices. The AT17A Series is packaged in the popular 20-lead PLCC and the 32-lead TQFP. The AT17A Series family uses a simple serial-access procedure to configure one or more FPGA devices ...
Page 2
Pin Configuration 20-lead PLCC DCLK 4 WP1 Block Diagram SER_EN WP1 OSC CONTROL OSC POWER-ON RESET DCLK READY AT17C/LV002A 2 18 SER_EN READY 14 NC PROGRAMMING MODE LOGIC ...
Page 3
Device The control signals for the configuration EEPROM (nCS, OE and DCLK) interface directly with the FPGA device control signals. All FPGA devices can control the entire configuration pro- Configuration cess and retrieve data from the configuration EEPROM without requiring ...
Page 4
Figure 1. Configuration with a Single AT17A Series Configurator EPF6K/EPF10K DCLK nCONFIG m 0.1 F DATA0 nCE CONF_DONE MSEL0 nSTATUS MSEL1 GND Notes: 1. Use of the READY pin is optional. 2. Introducing an RC ...
Page 5
... The programming is done at V Mode gramming supervoltages are generated inside the chip. See the “Programming Specification for Atmel’s Configuration EEPROMs” application note for further information. The AT17 A- series parts are read/write at 5V nominal. The AT17LV A-series parts are read/write at 3.3V nominal. ...
Page 6
... Device selection input, A2. This is used to enable (or select) the device during programming, (i.e., when SER_EN is Low; please refer to the “Programming Specification for Atmel’s Configuration EEPROMs” application note for more details.) Open collector reset state indicator. Driven Low during power-up reset, released (tri-stated) when power-up is complete. (Recommend a 4.7 kΩ ...
Page 7
... Operating Conditions is not implied. Exposure to CC Absolute Maximum Ratings conditions for extended periods of time may affect device reliability. AT17C002A Min 4.75 4.5 4.5 AT17LV002A Max Min Max Units 5 ...
Page 8
DC Characteristics ± 5% Commercial/5V ± 10% Industry/Military CC Symbol Description V High-level Input Voltage IH V Low-level Input Voltage IL V High-level Output Voltage ( Low-level Output Voltage ( High-level Output Voltage ...
Page 9
AC Characteristics nCS OE DCLK DATA AC Characteristics When Cascading OE nCS DCLK T CDF DATA LAST BIT T OCK nCASL 2280B–08/01 T SCE CAC T OCE T SCE T T ...
Page 10
... DCLK High Time Master Mode HC Notes: 1. Preliminary specifications for military operating range only test load = 50 pF. 3. Float delays are measured with loads. Transition is measured ± 200 mV from steady state active levels. AC Characteristics for AT17C002A When Cascading ± 5% Commercial ± 10% Industry/Military CC CC ...
Page 11
AC Characteristics for AT17LV002A V = 3.3V ± 5% Commercial Symbol Description ( Data Delay OE (2) T nCS to Data Delay CE (2) T DCLK to Data Delay CAC T Data Hold From ...
Page 12
... Ordering Information – 5V Devices Memory Size Ordering Code (1) 2-Mbit AT17C002A-10JC AT17C002A-10JI (1) 2-Mbit AT17C002A-10QC AT17C002A-10QI Note: 1. Use 2-Mbit density parts to replace Altera EPC2. Ordering Information – 3.3V Devices Memory Size Ordering Code (1) 2-Mbit AT17LV002A-10JC AT17LV002A-10JI (1) 2-Mbit AT17LV002A-10QC AT17LV002A-10Q1 Note: 1. Use 2-Mbit density parts to replace Altera EPC2. Atmel AT127C/LV002A devices do not support JTAG programming; Atmel AT17X002A devices use a 2-wire serial interface for in-system programming ...
Page 13
Packaging Information 20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-018 AA AT17C/LV002A 13 32A, 32-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) Dimensions in Millimeters and (Inches) PIN 1 ID ...
Page 14
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...