PCF8576DT/2,118 NXP Semiconductors, PCF8576DT/2,118 Datasheet - Page 32
![IC LCD DRIVER 40/160SEG 56TSSOP](/photos/6/90/69069/56-tssop_sml.jpg)
PCF8576DT/2,118
Manufacturer Part Number
PCF8576DT/2,118
Description
IC LCD DRIVER 40/160SEG 56TSSOP
Manufacturer
NXP Semiconductors
Datasheet
1.PCF8576DT2118.pdf
(50 pages)
Specifications of PCF8576DT/2,118
Package / Case
56-TSSOP
Display Type
LCD
Configuration
40 Segment
Interface
I²C
Current - Supply
24µA
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Number Of Digits
20
Number Of Segments
160
Maximum Clock Frequency
400 KHz
Operating Supply Voltage
1.8 V to 5.5 V
Maximum Power Dissipation
400 mW
Maximum Operating Temperature
+ 85 C
Maximum Supply Current
50 mA
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
568-4703 - DEMO BOARD LCD GRAPHIC DRIVER
Digits Or Characters
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-3558-2
935276166118
PCF8576DT/2-T
935276166118
PCF8576DT/2-T
NXP Semiconductors
12. Application information
PCF8576D
Product data sheet
12.1 Cascaded operation
In large display configurations, up to 16 PCF8576Ds can be differentiated on the same
I
programmable I
Table 17.
PCF8576Ds connected in cascade are synchronized to allow the backplane signals from
only one device in the cascade to be shared. This arrangement is cost-effective in large
LCD applications since the backplane outputs of only one device need to be
through-plated to the backplane electrodes of the display. The other cascaded
PCF8576Ds contribute additional segment outputs but their backplane outputs are left
open-circuit (see
All PCF8576Ds connected in cascade are correctly synchronized by the SYNC signal.
This synchronization is guaranteed after the power-on reset. The only time that SYNC is
likely to be needed is if synchronization is lost accidentally, for example, by noise in
adverse electrical environments, or if the LCD multiplex drive mode is changed in an
application using several cascaded PCF8576Ds, as the drive mode cannot be changed
on all of the cascaded devices simultaneously. SYNC can be either an input or an output
signal; a SYNC output is implemented as an open-drain driver with an internal pull-up
resistor. The PCF8576D asserts SYNC at the start of its last active backplane signal and
monitors the SYNC line at all other times. If cascade synchronization is lost, it is restored
by the first PCF8576D to assert SYNC. The timing relationship between the backplane
waveforms and the SYNC signal for each LCD drive mode is shown in
Cluster
1
2
2
C-bus by using the 3-bit hardware subaddresses (A0, A1 and A2) and the
Addressing cascaded PCF8576D
Bit SA0
0
1
All information provided in this document is subject to legal disclaimers.
2
C-bus slave address (SA0).
Figure
Rev. 10 — 14 February 2011
22).
Pin A2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
Universal LCD driver for low multiplex rates
Pin A1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
Pin A0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
PCF8576D
Figure
© NXP B.V. 2011. All rights reserved.
Device
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
23.
32 of 50