HIP1012ACB Intersil, HIP1012ACB Datasheet
![IC CTRLRL HOT PLUG DUAL 14-SOIC](/photos/5/65/56531/20-14-soic_sml.jpg)
HIP1012ACB
Specifications of HIP1012ACB
Available stocks
Related parts for HIP1012ACB
HIP1012ACB Summary of contents
Page 1
... PART NUMBER RANGE (°C) PACKAGE HIP1012ACB - SOIC HIP1012ACBZA (Note SOIC( Pb-free) M14.15 NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J Std-020B ...
Page 2
Simplified Block Diagram 12VIN C 20Ω GATE OPTIONAL R V FILTER DD C FILTER 20Ω C GATE 5VIN R SENSE 12VS R OC CLIM + - 2R 12VG FALLING - EDGE + DELAY 3X 18V ENABLE 18V ...
Page 3
Pin Descriptions PIN # SYMBOL FUNCTION 1 3V/12VS 3.3 V/12V Source 2 3V/12VG 3.3V/12V Gate 3 V Chip Supply DD 4 MODE/ Power ON/ Reset PWRON1 Invokes 3.3V operation when shorted PWRON2 Power ON/ Reset 6 5VG ...
Page 4
Absolute Maximum Ratings T = 25° ...
Page 5
Electrical Specifications V = 12V PARAMETER Gate Turn-On Current 3X Gate Discharge Current 5V Undervoltage Threshold 3.3V Undervoltage Threshold 3.3/5VG High Voltage SUPPLY CURRENT AND IO SPECIFICATIONS V Supply Current DD V POR Rising ...
Page 6
TABLE 1. R RESISTOR NOMINAL OC VTH ILIM 15kΩ 10kΩ 7.5kΩ 4.99kΩ NOTE: Nominal OC Vth = Rilim x 10µA. TABLE 2. C CAPACITOR NOMINAL TIME OUT PERIOD TIM 0.022µF 0.047µF 0.1µF NOTE: Nominal time-out period in seconds = C ...
Page 7
Typical Performance Curves 8.4 8.2 8.0 7.8 7.6 7.4 7.2 -40 -30 -20 - TEMPERATURE (°C) FIGURE 2. SUPPLY CURRENT 10.7 10.6 10.5 10.4 10.3 -40 -30 -20 - TEMPERATURE (°C) FIGURE ...
Page 8
Typical Performance Curves 17.36 17.34 12V VG 17.32 17.30 3.3V 17.28 17.26 -40 - TEMPERATURE (°C) FIGURE 8. 12V, 3/5V GATE DRIVE 54 Vth 54.0 53 Vth 53.0 52.5 -40 -20 ...
Page 9
Exploring and Using the HIP1012EVAL1 Board (Figures 13 and 14) The HIP1012EVAL1 is a flexible platform for a thorough evaluation of the HIP1012A dual power supply controller. This eval board comes in three separate parts allowing the evaluation of two ...
Page 10
CEC1 3 /12VIN GND GND JP1 0.1µ 20Ω NOTE: Test point number equals HIP1012A pin number. CEF SW13 CEF 1,2,3 R102 SW14 LED2 CEF 4,5,6, 7,8,10 SW11 CEF 9,11, ...
Page 11
FIGURE 14. HIP1012EVAL1 EVAL BOARD ...
Page 12
... TABLE 5. HIP1012EVAL1 BOARD COMPONENT LISTING COMPONENT DESIGNATOR COMPONENT NAME GENERIC BOARD U1 HIP1012CB or HIP1012ACB Q1, Q2 RF1K49156, Si4404DY QxB and QxC NOT POPULATED R 5V Sense Resistor 1 R 3.3V/12V Sense Resistor Loop compensation Resistors Current Limit Set Resistor 5 R* Isolation resistor (not provided, see Decoupling ...
Page 13
HIP1012 Evaluation Circuit for Disk Drive Hot Swap HIP1012EVAL2 Introduction The HIP1012EVAL2 is specifically designed to test and demonstrate hot swapping of disk drives onto passive 12V and 5V power buses using the HIP1012 Hot-Swap control IC. The small size ...
Page 14
J2 12V GND JP1 10Ω 1% GND 0.1µ JP2 12VG CTIM PWRON1 PWRON2 PGOOD 5VG GND 20Ω 0.01µF RF1K49157 Q1 FIGURE 15. HIP1012 EVALUATION ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...