MAX6965ATE+ Maxim Integrated Products, MAX6965ATE+ Datasheet - Page 22

• Manufacturer Part Number: MAX6965ATE+
• Description: IC LED DRIVER LINEAR 16-TQFN
• Manufacturer: Maxim Integrated Products
• Type: Linear (I²C Interface)r

Specifications of MAX6965ATE+

• Topology: Open Drain, PWM
• Number Of Outputs: 9
• Internal Driver: Yes
• Type - Primary: Backlight, LED Blinker
• Type - Secondary: RGB, White LED
• Frequency: 400kHz
• Voltage - Supply: 2 V ~ 3.6 V
• Voltage - Output: 7V
• Mounting Type: Surface Mount
• Package / Case: 16-TQFN Exposed Pad
• Operating Temperature: -40°C ~ 125°C
• Current - Output / Channel: 50mA
• Internal Switch(s): Yes
• Number Of Segments: 6
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Supply Current: 110 uA
• Maximum Power Dissipation: 1176 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Efficiency: -
• Lead Free Status / Rohs Status: Details

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
22
© 2005 Maxim Integrated Products
9-Output LED Driver with Intensity Control
and Hot-Insertion Protection
____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
PKG
REF.
NE
A2
ND
A1
NOTES:
D
A
b
E
e
L
N
k
10. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
11. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
12. WARPAGE NOT TO EXCEED 0.10mm.
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220 REVISION C.
MIN.
0.70
0.35
0.25
0.25
2.90
2.90
0
JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED
WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE.
FROM TERMINAL TIP.
0.65 BSC.
0.20 REF
8L 3x3
NOM. MAX.
0.75
0.30
3.00
3.00
0.55
0.02
8
2
2
-
MARKING
0.80
0.35
3.10
3.10
0.75
0.05
D
-
D/2
0.10 C
MIN.
0.70
2.90
2.90
0.45
0.25
0.20
0
0.50 BSC.
0.20 REF
12L 3x3
NOM. MAX.
0.75
0.25
3.00
3.00
0.55
0.02
E/2
12
3
3
-
AAAA
0.30
0.80
3.10
0.65
0.05
3.10
Printed USA
L C
E
-
A
A2
A1
0.08 C
MIN.
2.90
0.30
0.25
0.70
0.20
2.90
0
0.50 BSC.
0.20 REF
16L 3x3
NOM.
3.00
0.75
0.25
3.00
0.40
0.02
16
4
4
-
L C
MAX.
0.80
0.30
3.10
3.10
0.50
0.05
-
CODES
T1633FH-3
PKG.
TQ833-1
T1233-1
T1233-3
T1233-4
T1633-2
T1633F-3
T1633-4
T1633-5
L
MIN.
0.25
0.95
0.95
0.95
0.95
0.65
0.65
0.95
0.95
L C
e
NOM.
0.80
0.70
1.10
1.10
1.10
1.10
0.80
1.10
1.10
Package Information (continued)
EXPOSED PAD VARIATIONS
D2
is a registered trademark of Maxim Integrated Products, Inc.
(ND - 1) X e
e
MAX.
0.95
1.25
1.25
1.25
1.25
1.25
0.95
1.25
1.25
k
0.25
0.65
MIN.
0.95
0.95
0.95
0.95
0.65
0.95
0.95
L
(NE - 1) X e
NOM.
0.80
0.70
1.10
1.10
1.10
1.10
0.80
1.10
1.10
E2
E2
PACKAGE OUTLINE
8, 12, 16L THIN QFN, 3x3x0.8mm
PACKAGE OUTLINE
8, 12, 16L THIN QFN, 3x3x0.8mm
E2/2
MAX.
0.95
1.25
1.25
1.25
1.25
1.25
0.95
1.25
1.25
0.225 x 45°
0.35 x 45°
0.35 x 45°
0.35 x 45°
0.35 x 45°
0.35 x 45°
0.225 x 45°
0.35 x 45°
0.35 x 45°
PIN ID
e
C L
21-0136
21-0136
D2/2
b
WEED-2
WEEC
WEED-1
WEED-1
WEED-1
WEED-2
WEED-2
WEED-2
WEED-2
JEDEC
D2
0.10 M C A B
L
I
I
1
2
2
2