LT3003EMSE#PBF Linear Technology, LT3003EMSE#PBF Datasheet - Page 6
![IC LED DRIVER BALLASTER 10-MSOP](/photos/6/59/65968/161-10-msop_sml.jpg)
LT3003EMSE#PBF
Manufacturer Part Number
LT3003EMSE#PBF
Description
IC LED DRIVER BALLASTER 10-MSOP
Manufacturer
Linear Technology
Type
LED Ballasterr
Datasheet
1.LT3003EMSEPBF.pdf
(16 pages)
Specifications of LT3003EMSE#PBF
Topology
PWM, Step-Down (Buck), Step-Up (Boost)
Number Of Outputs
3
Internal Driver
Yes
Type - Primary
Automotive, Backlight
Voltage - Supply
3 V ~ 40 V
Mounting Type
Surface Mount
Package / Case
10-MSOP Exposed Pad, 10-HMSOP, 10-eMSOP
Operating Temperature
-40°C ~ 125°C
Current - Output / Channel
350mA
Internal Switch(s)
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Frequency
-
Efficiency
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
OPERATION
LT3003
The LT3003 is an easy-to-use 3-channel LED ballaster.
It allows three strings of LEDs to be driven in parallel
with accurate LED current matching. A PWM pin is also
provided allowing LED currents to be turned on and off at
very low duty cycles for very wide LED dimming ranges.
For reliable system thermal management, two output fl ags,
OT1 and OT2, are provided to indicate when the junction
temperature exceeds 125°C.
The Block Diagram in Figure 1 best illustrates the features
of LT3003. The LT3003 internal bias circuitry is turned on
when V
active in each channel, the PWM pin must exceed 0.5V.
V
application (see various application modes of boost, buck,
buck-boost in the Typical Applications section).
The LT3003 ballasting feature is achieved by using the
current monitored in the LED2 channel to control the
current in channels LED1 and LED3. A servo loop exists
for each channel LED1 and LED3 that compares the cur-
rent in each channel to the LED2 reference channel. The
current in LED2 channel is determined by the LED current
programmed by the partner LED driver. Details of how LED
current can be programmed by the partner IC are covered
in the Typical Applications section using various ICs as
LED drivers. Maximum fault current in each of the LT3003
LED pins is internally limited to 550mA. If any LED string
experiences an open-circuit fault, all LED string currents
are turned off.
6
MAX
should be connected to the highest supply in the
IN
> 3V and SHDN > 0.7V. For LED current to be
The LT3003 PWM pin has unique level-shifting circuitry to
allow a simple logic-level PWM signal to turn each LED pin
current on and off regardless of the V
allows very simple PWM dimming control of LED current
without any need for external level-shifting components
in buck mode and buck-boost mode applications. Care is
taken to ensure low current (nano amps) in the V
V
mizes leakage currents in each application to maximize
PWM dimming ratio. Details of PWM dimming and criti-
cal parameters are given in the Applications Information
section PWM Dimming.
The LT3003 incorporates internal junction temperature
sensing and provides two open-collector outputs, OT1
and OT2, which become active low when junction tem-
perature exceeds 125°C. OT1 is sized to pull 100µA and
can be used as an input to the microprocessor for system
thermal management. OT2 is sized to pull 300µA to defeat
switching for most of LTC’s LED drivers by pulling down
the g
LED current state” by a special internal protection circuit
when junction temperature reaches 150°C.
To calculate the LT3003 junction temperature, see Thermal
Calculations in the Applications Information section.
MAX
m
pins 10µs after PWM low edge. This feature mini-
error amplifi er output. LT3003 is forced to a “zero
EE
pin voltage. This
EE
3003fa
and