PCA9624PW,118 NXP Semiconductors, PCA9624PW,118 Datasheet - Page 32

• Manufacturer Part Number: PCA9624PW,118
• Description: IC LED DRIVER RGBA 24-TSSOP
• Manufacturer: NXP Semiconductors
• Type: RGBA LED Driverr

Specifications of PCA9624PW,118

• Package / Case: 24-TSSOP
• Topology: Open Drain, PWM
• Number Of Outputs: 8
• Internal Driver: Yes
• Type - Primary: Backlight, LED Blinker
• Type - Secondary: RGBA
• Frequency: 1MHz
• Voltage - Supply: 2.3 V ~ 5.5 V
• Voltage - Output: 40V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 100mA
• Internal Switch(s): Yes
• Low Level Output Current: 20 mA
• Operating Supply Voltage: 2.3 V to 5.5 V
• Maximum Supply Current: 10 mA
• Maximum Power Dissipation: 100 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Efficiency: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 03118 863 9352

NXP Semiconductors
17. Handling information
18. Soldering of SMD packages
PCA9624_2
Product data sheet
18.1 Introduction to soldering
18.2 Wave and reflow soldering
18.3 Wave soldering
All input and output pins are protected against ElectroStatic Discharge (ESD) under
normal handling. When handling ensure that the appropriate precautions are taken as
described in JESD625-A or equivalent standards.
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description” .
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
Key characteristics in wave soldering are:
•
•
•
•
•
•
•
•
Through-hole components
Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
Rev. 02 — 26 August 2009
8-bit Fm+ I
2
C-bus 100 mA 40 V LED driver
PCA9624
© NXP B.V. 2009. All rights reserved.
32 of 37