TLE7189F Infineon Technologies, TLE7189F Datasheet - Page 18

• Manufacturer Part Number: TLE7189F
• Description: IC DRIVER 3PH BRIDGE 48-VQFN
• Manufacturer: Infineon Technologies
• Type: High Side/Low Sider

Specifications of TLE7189F

• Applications: DC Motor Driver, 3 Phase
• Number Of Outputs: 1
• Voltage - Supply: 5.5 V ~ 28 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: 48-VFQFN
• Rise Time: 400 ns
• Fall Time: 230 ns
• Supply Voltage (min): 5.5 V
• Supply Current: 110 mA
• Maximum Operating Temperature: + 150 C
• Mounting Style: SMD/SMT
• Bridge Type: 3-Phase Bridge
• Minimum Operating Temperature: - 40 C
• Number Of Drivers: 3
• Packages: PG-VQFN-48
• Operating Range: 5.5 - 28.0 V
• Iq: 30 ?A
• Turn On/off Current: 1.5/ 1.5 A
• D.c.-range @ 20khz: 0...100%
• Numbers Of Integrated Opamps For Load Current Measurement: 3.0
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Voltage - Load: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SP000248208; TLE7189F; TLE7189FINTR

Under voltage shut down will not occur when
Cxx = 4.7 µF.
5.2.4
The TLE7189F has an integrated over voltage shut down to avoid destruction of the IC at high supply voltages.The
voltage is measured at the Vs and the VDH pin. When one of them or all of them exceed the over voltage shut
down level for more than the specified filter time then the external MOSFETs are switched off. In addition, over
voltage will shut down the charge pumps and will discharge the charge pump capacitors. This results in an under
voltage condition which will be indicated on the ERRx pins. During over voltage shut down the external MOSFETs
and the charge pumps remain off until a reset is performed.
5.2.5
If the junction temperature is exceeding typ. 155°C an error signal is given as warning. The driver IC will continue
to operate in order not to disturb the application.
The warning is removed automatically when the junction temperature is cooling down.
It is in the responsibility of the user to protect the device against over temperature destruction.
5.2.6
To assure a high level of system safety, the TLE7189F provides an VCC check.
The 5.0V system supply connected to the VS_OA pin is checked by an internally monitoring for over- and under
voltage. An internal filter time is integrated to avoid faulty triggering.
The VCC check is active when the signal on the ENA pin is high and inactive when ENA signal is low (=driver IC
disabled).
In case of under- or over voltage at VS_OA, the VCC check will disable the driver IC and is latched. To restart the
output stages, a reset has to be performed with the ENA pin.
The VCT pin decides about the over voltage and under voltage detection level.
5.2.7
The TLE7189F has two status pins to provide diagnostic feedback to the µC. The outputs of these pins are 5V
push pull stages, they are either High or Low.
Table 2
Table 3
Data Sheet
INH
High
High
High
High
High
Low
Error condition
Short circuit detection
Under voltage
Over voltage
ENA
High
High
High
High
Low
X
Over Voltage Shut Down
Over Temperature Warning
VCC Check
ERR Pins
Overview of error conditions
Behavior at different error conditions
ERR1
Low
Low
High
High
High
Low
restart behavior
Latch, reset must be performed at ENA pin All external Power -MOSFETs
Auto restart
Latch, reset must be performed at ENA pin All external Power -MOSFETs
ERR2
Low
High
Low
High
High
Low
Driver conditions
Under voltage or VCC check error
Over temperature or over voltage
Short circuit detection
No errors observed
No errors will be reported
ERR output tristate - low secured by pull down
V
S
> 6V,
Q
G
18
< 250nC,
f
PWM
< 25kHz, and the charge pump capacitors
Shuts down...
All external Power -MOSFETs
Rev. 2.1, 2007-05-30
TLE7189F