HCPL-800J-000E Avago Technologies US Inc., HCPL-800J-000E Datasheet - Page 8

• Manufacturer Part Number: HCPL-800J-000E
• Description: OPTOCOUPLER DAA PLC ISO 16SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-800J-000E

• Package / Case: SO-16
• Mounting Type: Surface Mount
• Current - Supply: 28mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Applications: Powerline Data Access
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Unless otherwise noted, for sinusoidal waveform input and reference resistor R
= 25°C, V
Transmitter
Notes:
1. Time from transmit is enabled (V
2. Time from output (Tx-PD-out) is available until Tx-PD-out signal reaches 66% of its steady state level. See Figure 26 in the Application
3. To keep the junction temperature as close to the ambient temperature as possible, pulse testing method is used. The device is transmit-
4. Maximum power dissipation in Control side and Line side IC’s needs to be limited to ensure that their respective junction temperature is less
Parameter
Transmit Enable Threshold
Voltage
Set-up Time (Tx-PD-out)
AGC Settling Time
Tx Photodetector Output
Voltage (Tx-PD-out)
2nd Harmonic Distortion
Tx-PD-out)
3rd Harmonic Distortion
(Tx-PD-out)
Bandwidth (Tx-PD-out)
Tx Photodetector Output
Impedance (Tx-PD-out)
Line Driver (LD)
Power Supply (V
Rejection Ratio
Input Impedance
DC Biased Voltage
Gain
2nd Harmonic Distortion
(Tx-out)
3rd Harmonic Distortion
(Tx-out)
Output Impedance (Tx-out)
Short-Circuit Output Current I
enabled within the pulse duration time, t
section.
Information section.
than 125°C. The maximum permissible power dissipation is dependent on the thermal impedance and the ambient temperature. Details on
the typical thermal impedances are given in the Package Characteristics. Further details on applying this to an actual application can be
found in the Application Information section under Thermal Considerations.
CC1
= 5 V, V
CC2
CC2
)
= 5 V; all Minimum/Maximum specifications are at Recommended Operating Conditions.
Tx-en
is set to logic high) until output (Tx-PD-out) is available. See Figure 26 in the Application Information
Symbol
V
t
t
HD2
HD3
BW
Z
PSRR
Z
V
G
HD2
HD3
Z
OS
s
AGC
th
, T
O
I, LD
Bias
O, LD
T2
,
, T
P
TxPD
x
TxPD
. Thermal effects must be considered separately.
, LD
TxPD
TxPD
LD
LD
x-en
Min.
0.8
2.8
1.8
Typ. Max.
10
180
3.3
-50
-62
1
1
55
10
2.27
2
-65
-75
0.5
7.5
2
2.4
3.6
2.2
-60
-65
Unit Test Condition
V
µs
µs
V
dB
dB
MHz V
Ω
dB
kΩ
V
V/V
dB
dB
Ω
kΩ
A
PP
V
f = 132 kHz,
Tx-PD-out no load
V
f = 132 kHz, T
V
f = 132 kHz, Tx-PD-out
load 1
V
50 Hz ripple,
V
V
V
V
out no load
V
f = 132 kHz, Tx-out load
50 Ω, T
V
V
V
V
f = 132 kHz, t
ripple
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-en
Tx-LD-in
= 5 V, f = 132 kHz, Tx-
= 5 V, f = 132 kHz
= 0 V, f = 132 kHz
= 5 V, I
= 5 V, I
= 5 V, I
= 5 V, I
= 5 V, f = 132 kHz
= 5 V, f = 132 kHz
= 5 V
= 5 V, V
= 5 V,
= 200 mV
ref
kΩ
A
= 1.8 V
= 24 kΩ, all typical values are at T
= 25°C
Tx-in
Tx-in
Tx-in
Tx-in
Tx-out
P
A
PP
≤
= 25°C
PP
,
= 250 µA
= 250 µA
= 250 µA
= 250µA
50 µs
= 3.6 V
PP
PP
PP
PP
PP
,
,
,
,
Fig.
21
7, 8, 9
10, 22
11
12, 13,
14, 15,
16, 23
Note
1
2
3, 4
A