ISL62392HRTZ Intersil, ISL62392HRTZ Datasheet - Page 5

IC PWR SUPPLY CONTROLLER 28TQFN

ISL62392HRTZ

Manufacturer Part Number
ISL62392HRTZ
Description
IC PWR SUPPLY CONTROLLER 28TQFN
Manufacturer
Intersil
Datasheet

Specifications of ISL62392HRTZ

Applications
Power Supply Controller
Voltage - Supply
5.5 V ~ 25 V
Current - Supply
150µA
Operating Temperature
-10°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
28-TQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Input
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL62392HRTZ
Manufacturer:
Intersil
Quantity:
35
Part Number:
ISL62392HRTZ
Manufacturer:
INTESIL
Quantity:
20 000
Company:
Part Number:
ISL62392HRTZ
Quantity:
248
Part Number:
ISL62392HRTZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Functional Pin Description
Bottom
PIN
Pad
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
11
1
2
3
4
5
6
7
8
9
LDO3EN
OCSET1
PHASE1
UGATE1
UGATE2
PHASE2
OCSET2
PGOOD
LGATE1
LGATE2
VOUT1
BOOT1
BOOT2
VOUT2
FSET2
FSET1
NAME
FCCM
ISEN1
PGND
ISEN2
PVCC
LDO3
GND
VCC
EN1
EN2
FB1
FB2
VIN
Open-drain power-good status outputs. Connect to VCC through a 100k resistor. Output will be high when all outputs are
within regulation with no faults detected.
Frequency control input for SMPS2. Connect a resistor to ground to program the switching frequency. The pin output is
a pulsed current and requires a decoupling capacitor to average the signal.
Logic input to control efficiency mode. Logic high forces continuous conduction mode (CCM). Logic low allows full
discontinuous conduction mode (DCM). Float this pin for ultrasonic DCM operation.
Analog power supply input for reference voltages and currents. Bypass to ground with a 1µF ceramic capacitor near the IC.
Logic input for enabling and disabling the LDO3 linear regulator. Positive logic input.
Frequency control input for SMPS1. Connect a resistor to ground to program the switching frequency. The pin output is
a pulsed current and requires a decoupling capacitor to average the signal.
SMPS1 feedback input used for output voltage programming and regulation.
SMPS1 output voltage sense input. Used for soft-discharge.
SMPS1 DCR current sense input. Used for overcurrent protection and R
Input from DCR current-sensing network used to program the overcurrent shutdown threshold for SMPS1.
Logic input to enable and disable SMPS1. A logic high will immediately enable SMPS1. Floating this pin will enable
SMPS1 only after SMPS2 has been enabled and achieved regulation. A logic low disables SMPS1.
SMPS1 switching node for high-side gate drive return and synthetic ripple modulation. Connect to the switching NMOS
source, the synchronous NMOS drain, and the output inductor for SMPS1.
High-side NMOS gate drive output for SMPS1. Connect to the gate of the SMPS1 switching FET.
SMPS1 bootstrap input for the switching NMOS gate drivers. Connect to SMPS1 PHASE with a ceramic capacitor of 0.22µF.
Low-side NMOS gate drive output for SMPS1. Connect to the gate of the SMPS1 synchronous FET.
3.3V linear regulator output, capable of providing 100mA continuous current. Bypass to ground with a 4.7µF ceramic capacitor.
Feed-forward input for line voltage transient compensation. Connect to the power train input voltage.
5V power source for SMPS gate drive current. Bypass to ground with a 4.7µF ceramic capacitor.
Power ground for SMPS1 and SMPS2. This provides a return path for synchronous FET switching currents.
Low-side NMOS gate drive output for SMPS2. Connect to the gate of the SMPS2 synchronous FET.
SMPS2 bootstrap input for the switching NMOS gate drivers. Connect to SMPS2 PHASE with a ceramic capacitor of 0.22µF.
High-side NMOS gate drive output for SMPS2. Connect to the gate of the SMPS2 switching FET.
SMPS2 switching node for high-side gate drive return and synthetic ripple modulation. Connect to the switching NMOS
source, the synchronous NMOS drain, and the output inductor for SMPS2.
Logic input to enable and disable SMPS2. A logic high will immediately enable SMPS2. Floating this pin will enable
SMPS2 only after SMPS1 has been enabled and achieved regulation. A logic low disables SMPS2.
Input from DCR current-sensing network used to program the overcurrent shutdown threshold for SMPS2.
SMPS2 DCR current sense input. Used for overcurrent protection and R
SMPS2 output voltage sense input. Used for soft-discharge and switchover for PVCC 5V LDO.
SMPS2 feedback input used for output voltage programming and regulation.
Analog ground for analog and logic signals.
5
ISL62391, ISL62392, ISL62391C, ISL62392C
FUNCTION
3
3
regulation.
regulation.
April 7, 2011
FN6666.5

Related parts for ISL62392HRTZ