ISL6535CRZ-T Intersil, ISL6535CRZ-T Datasheet - Page 11

• Manufacturer Part Number: ISL6535CRZ-T
• Description: IC CTRLR SYNC BUCK PWM 16-QFN
• Manufacturer: Intersil

Specifications of ISL6535CRZ-T

• Pwm Type: Voltage Mode
• Number Of Outputs: 1
• Frequency - Max: 1.5MHz
• Duty Cycle: 100%
• Voltage - Supply: 10.8 V ~ 13.2 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 16-VQFN Exposed Pad, 16-HVQFN, 16-SQFN, 16-DHVQFN
• Frequency-max: 1.5MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

voltage and the initial voltage drop after a high slew-rate
transient. An aluminum electrolytic capacitor's ESR value is
related to the case size with lower ESR available in larger
case sizes. However, the equivalent series inductance
(ESL) of these capacitors increases with case size and can
reduce the usefulness of the capacitor to high slew-rate
transient loading. Unfortunately, ESL is not a specified
parameter. Work with your capacitor supplier and measure
the capacitor’s impedance with frequency to select a
suitable component. In most cases, multiple electrolytic
capacitors of small case size perform better than a single
large case capacitor.
Output Inductor Selection
The output inductor is selected to meet the output voltage
ripple requirements and minimize the converter’s response
time to the load transient. The inductor value determines the
converter’s ripple current and the ripple voltage is a function
of the ripple current. The ripple voltage and current are
approximated by Equation 15:
Increasing the value of inductance reduces the ripple current
and voltage. However, the large inductance values reduce
the converter’s response time to a load transient.
One of the parameters limiting the converter’s response to a
load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6535 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval the
difference between the inductor current and the transient
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient load is different for the
application of load and the removal of load. The following
equations give the approximate response time interval for
application and removal of a transient load:
where: I
response time to the application of load, and t
response time to the removal of load. With a +5V input
source, the worst case response time can be either at the
application or removal of load and dependent upon the output
voltage setting. Be sure to check both of these equations at
the minimum and maximum output levels for the worst case
response time.
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
ΔI =
t
RISE
V
------------------------------- -
IN
=
TRAN
Fs x L
------------------------------- -
V
L
- V
O
IN
OUT
×
–
I
is the transient load current step, t
TRAN
V
OUT
•
V
--------------- -
V
OUT
IN
t
FALL
11
ΔV
=
OUT
L
------------------------------ -
O
= ΔI x ESR
V
×
OUT
I
TRAN
FALL
RISE
is the
(EQ. 15)
(EQ. 16)
is the
ISL6535
capacitors for high frequency decoupling and bulk capacitors
to supply the current needed each time Q
small ceramic capacitors physically close to the MOSFETs
and between the drain of Q
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select a bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25 times greater than the maximum
input voltage, a voltage rating of 1.5 times greater is a
conservative guideline. The RMS current rating requirement
for the input capacitor of a buck regulator is approximately
1/2 the DC load current.
For a through hole design, several electrolytic capacitors
(Panasonic HFQ series or Nichicon PL series or Sanyo MV-
GX or equivalent) may be needed. For surface mount
designs, solid tantalum capacitors can be used, but caution
must be exercised with regard to the capacitor surge current
rating. These capacitors must be capable of handling the
surge-current at power-up. The TPS series available from
AVX, and the 593D series from Sprague are both surge
current tested.
MOSFET Selection/Considerations
The ISL6535 requires at least 2 N-Channel power MOSFETs.
These should be selected based upon r
requirements, and thermal management requirements.
In high-current applications, the MOSFET power dissipation,
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss
components; conduction loss and switching loss. At a
300kHz switching frequency, the conduction losses are the
largest component of power dissipation for both the upper
and the lower MOSFETs. These losses are distributed
between the two MOSFETs according to duty factor (see
Equation 17). Only the upper MOSFET exhibits switching
losses, since the schottky rectifier clamps the switching node
before the synchronous rectifier turns on.
These equations assume linear voltage-current transitions
and do not adequately model power loss due the reverse-
recovery of the lower MOSFETs body diode. The
gate-charge losses are dissipated by the ISL6535 and don't
heat the MOSFETs. However, large gate-charge increases
the switching interval, t
MOSFET switching losses. Ensure that both MOSFETs are
within their maximum junction temperature at high ambient
P
where: D is the duty cycle = V
P
LOWER
UPPER
t
f
= I
= I
SW
SW
O
O
2
2
is the switching interval, and
is the switching frequency.
x r
x r
DS(ON)
DS(ON)
SW
x D +
x (1 - D)
1
which increases the upper
and the source of Q
1
2
O
Io x V
/ V
IN
IN
,
DS(ON)
x t
1
SW
turns on. Place the
x f
, gate supply
SW
2
.
May 5, 2008
(EQ. 17)
FN9255.1