ISL6740AIVZA-T Intersil, ISL6740AIVZA-T Datasheet
ISL6740AIVZA-T
Specifications of ISL6740AIVZA-T
Related parts for ISL6740AIVZA-T
ISL6740AIVZA-T Summary of contents
Page 1
... Ordering Information TEMP. RANGE PART NUMBER (°C) PACKAGE ISL6740AIVZA -40 to 105 16 Ld TSSOP (Note) (Pb-free) Add -T suffix to part number for tape and reel packaging NOTE: Intersil Pb-free products employ special Pb-free material sets ...
Page 2
Functional Block Diagram REF V REF 5. ENABLE + - + BG - GND N_SYNC OUT Internal OT Shutdown 130 - 150 C Synchronization INHIBIT 1. EXT. SYNC INHIBIT UV/FF - ...
Page 3
Typical Application - 48V Input Bus Converter 10A Output VIN 36-75V VIN CR1 CR2 VDD R13 2 HB VSS ...
Page 4
Typical Application - Input, Regulated 12V @ 8A Output VIN 36-75V VIN VR1 CR1 CR2 R14 U1 1 VDD LO 8 R13 ...
Page 5
Absolute Maximum Ratings Supply Voltage GND - 0.3V to +20.0V DD OUTA, OUTB, Signal Pins . . . . . ...
Page 6
Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to Block Diagram and Typical Application Schematic. 9V < V values are at T PARAMETER Minimum Duty Cycle Maximum Duty Cycle V to PWM Comparator Input Gain ERROR C to PWM ...
Page 7
Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to Block Diagram and Typical Application Schematic. 9V < V values are at T PARAMETER SOFT-START Charging Current SS Clamp Voltage Sustained Overcurrent Threshold Voltage Overcurrent/Short Circuit Discharge Current Fault SS ...
Page 8
Typical Performance Curves 1.001 1 0.999 0.998 0.997 -40 -25 - TEMPERATURE (°C) FIGURE 1. REFERENCE VOLTAGE vs TEMPERATURE 4 1•10 CT (pF) = 1000 680 470 330 3 1•10 220 100 100 ...
Page 9
V - The inverting input of the PWM comparator. The ERROR error voltage is applied to this pin to control the duty cycle. Increasing the signal level increases the duty cycle. The node may be driven with an external error ...
Page 10
Oscillator The ISL6740A has an oscillator with a programmable frequency range to 2MHz, and can be programmed with two resistors and a capacitor. The use of three timing elements ...
Page 11
UV/Inhibit fault; otherwise inactive and does not affect the node voltage. The magnitude of the hysteresis is a function of the external resistor divider impedance. If the resistor divider impedance results in too little hysteresis, a series resistor ...
Page 12
SS 0 OUTA OUTB FIGURE 7. PULSE-BY-PULSE OC BEHAVIOR ...
Page 13
V SCSET ⋅ ---------------------- - D SC max 2 where D is the maximum short circuit duty cycle the voltage applied ...
Page 14
If the hysteresis resistor, R3, is not desired, the value of the thermistor resistance at the reset temperature can be determined from: • 2.5 R2 Ω ---------------------------------------- NTC – 5 • 2 – • ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...