GNM314R72A102KD01D Murata Electronics North America, GNM314R72A102KD01D Datasheet - Page 28

CAP 4-ARRAY 1000PF 100V X7R 1206

GNM314R72A102KD01D

Manufacturer Part Number
GNM314R72A102KD01D
Description
CAP 4-ARRAY 1000PF 100V X7R 1206
Manufacturer
Murata Electronics North America
Series
GNMr
Datasheet

Specifications of GNM314R72A102KD01D

Capacitance
1000pF
Voltage - Rated
100V
Dielectric Material
Ceramic
Number Of Capacitors
4
Circuit Type
Isolated
Temperature Coefficient
X7R
Tolerance
±10%
Mounting Type
Surface Mount
Package / Case
1206 (3216 Metric)
Height
0.031" (0.80mm)
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
490-3421-2
5
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
26
No.
11
12
13
GRM Series Specifications and Test Methods (1)
Continued from the preceding page.
Vibration
Resistance
Deflection
Solderability of
Termination
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Q/D.F.
No defects or abnormalities
Within the specified tolerance
30pF and over: QU1000
30pF and below:
C: Nominal Capacitance (pF)
No crack or marked defect should occur.
75% of the terminations are to be soldered evenly and
continuously.
Compensating Type
Temperature
Q U400W20C
In case "*" is added in capacitance table, please refer to GRM Series Specifications and Test Methods (2) (P.30).
R230
Below GRM Series Specifications and Test Methods (1) are applied to Non "*" PNs in capacitance table.
Capacitance meter
45
Fig. 3a
Specifications
20
50
45
Pressurize
[B1, B3, R6, R7, C8]
W.V.: 100V
W.V.: 50/25V
W.V.: 16/10V: 0.035 max.
W.V.: 6.3/4V
[E4]
W.V.: 25Vmin: 0.025 max.
[F1, F5]
W.V.: 25V min.
W.V.: 16/10V: 0.125 max.
W.V.: 6.3V: 0.15 max.
Pressurizing
speed : 1.0mm/sec.
: 0.025 max. (CF0.068µF)
: 0.05 max. (CU0.068µF)
High Dielectric Type
: 0.025 max. (CF10µF)
: 0.035 max. (CU10µF)
: 0.09 max. (CU0.1µF)
: 0.05 max. (CF3.3µF)
: 0.1 max. (CU3.3µF)
: 0.05 max. (CF0.1µF)
Flexure : V1
Solder the capacitor on the test jig (glass epoxy board) in the
same manner and under the same conditions as (10).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually
perpendicular directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2a using an eutectic solder. Then apply a force in the
direction shown in Fig. 3a for 5T1 sec. The soldering should be
done by the reflow method and should be conducted with care
so that the soldering is uniform and free of defects such as heat
shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion) .
Preheat at 80 to 120D for 10 to 30 seconds.
After preheating, immerse in an eutectic solder solution for
2T0.5 seconds at 230T5D or Sn-3.0Ag-0.5Cu solder solution
for 2T0.5 seconds at 245T5°C.
GRM02
GRM03
GRM15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
Type
0.2
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
Test Method
a
Fig. 2a
100
b
c
a
Continued on the following page.
t: 1.6mm (GRM02/03/15: t: 0.8mm)
0.56
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
b
4.5
0.23
1.65
0.3
0.5
1.2
2.0
2.9
3.7
5.6
c
(in mm)
C02E.pdf
07.2.6

Related parts for GNM314R72A102KD01D