MAX668EUB+T Maxim Integrated Products, MAX668EUB+T Datasheet - Page 8

• Manufacturer Part Number: MAX668EUB+T
• Description: IC PWM BST FLYBCK ISO CM 10UMAX
• Manufacturer: Maxim Integrated Products

Specifications of MAX668EUB+T

• Pwm Type: Current Mode
• Number Of Outputs: 1
• Frequency - Max: 575kHz
• Duty Cycle: 94%
• Voltage - Supply: 3 V ~ 28 V
• Buck: No
• Boost: Yes
• Flyback: Yes
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: Yes
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Frequency-max: 575kHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1.8V to 28V Input, PWM Step-Up
Controllers in µMAX
The MAX668/MAX669 current-mode PWM controllers
operate in a wide range of DC-DC conversion applica-
tions, including boost, SEPIC, flyback, and isolated out-
put configurations. Optimum conversion efficiency is
maintained over a wide range of loads by employing
both PWM operation and Maxim’s proprietary Idle
Mode control to minimize operating current at light
loads. Other features include shutdown, adjustable
internal operating frequency or synchronization to an
external clock, soft start, adjustable current limit, and a
wide (1.8V to 28V) input range.
Differences between the MAX668 and MAX669 relate
to their use in bootstrapped or non-bootstrapped cir-
cuits (Table 1). The MAX668 operates with inputs as
low as 3V and can be connected in either a boot-
strapped or non-bootstrapped (IC powered from input
supply or other source) configuration. When not boot-
strapped, the MAX668 has no restriction on output volt-
age. When bootstrapped, the output cannot exceed
28V.
The MAX669 is optimized for low input voltages (down
to 1.8V) and requires bootstrapped operation (IC pow-
ered from V
8
PIN
10
_______________________________________________________________________________________
1
2
3
4
5
6
7
8
9
NAME
SYNC/
PGND
SHDN
FREQ
GND
LDO
CS+
REF
EXT
V
FB
OUT
CC
MAX668 vs. MAX669 Differences
) with output voltages no greater than
5V On-Chip Regulator Output. This regulator powers all internal circuitry including the EXT gate driver.
Bypass LDO to GND with a 1µF or greater ceramic capacitor.
Oscillator Frequency Set Input. A resistor from FREQ to GND sets the oscillator from 100kHz (R
500kΩ) to 500kHz (R
at SYNC/SHDN (see the
Analog Ground
1.25V Reference Output. REF can source 50µA. Bypass to GND with a 0.22µF ceramic capacitor.
Feedback Input. The FB threshold is 1.25V.
Positive Current-Sense Input. Connect a current-sense resistor, R
Power Ground for EXT Gate Driver and Negative Current-Sense Input
External MOSFET Gate-Driver Output. EXT swings from LDO to PGND.
Input Supply to On-Chip LDO Regulator. V
capacitor.
Shutdown control and Synchronization Input. There are three operating modes:
Detailed Description
• SYNC/SHDN low: DC-DC off.
• SYNC/SHDN high: DC-DC on with oscillator frequency set at FREQ by R
• SYNC/SHDN clocked: DC-DC on with operating frequency set by SYNC clock input. DC-DC conversion
cycles initiate on rising edge of input clock.
OSC
SYNC/SHDN and FREQ Inputs section).
= 100kΩ). f
OSC
CC
= 5 x 10
accepts inputs up to 28V. Bypass to GND with a 0.1µF ceramic
28V. Bootstrapping is required because the MAX669
does not have undervoltage lockout, but instead drives
EXT with an open-loop, 50% duty-cycle start-up oscilla-
tor when LDO is below 2.5V. It switches to closed-loop
operation only when LDO exceeds 2.5V. If a non-boot-
strapped connection is used with the MAX669 and if
V
voltage will soar above the regulation point. Table 2
recommends the appropriate device for each biasing
option.
Table 1. MAX668/MAX669 Comparison
FEATURE
V
Range
Operation
UVLO
Soft-Start
CC
FUNCTION
CC
10
(the input voltage) remains below 2.7V, the output
Input
/ R
OSC
. R
3V to 28V
Bootstrapped or nonboot-
strapped. V
nected to input, output, or
other voltage source such as
a logic supply.
IC stops switching for LDO
below 2.5V.
Yes
OSC
CS
is still required if an external clock is used
, between CS+ and PGND.
MAX668
CC
can be con-
OSC
.
Pin Description
1.8V to 28V
Must be boot-
strapped (V
must be connect-
ed to boosted out-
put voltage, V
No
When LDO is
above 2.5V
OSC
MAX669
=
CC
OUT
).