ISL6244CR Intersil, ISL6244CR Datasheet - Page 20
![IC CTRLR PWM 2-4-PHASE 32-QFN](/photos/6/88/68833/32-qfn_pkg_sml.jpg)
ISL6244CR
Manufacturer Part Number
ISL6244CR
Description
IC CTRLR PWM 2-4-PHASE 32-QFN
Manufacturer
Intersil
Datasheet
1.ISL6244CRZ.pdf
(25 pages)
Specifications of ISL6244CR
Pwm Type
Voltage/Current Mode
Number Of Outputs
4
Frequency - Max
4MHz
Duty Cycle
75%
Voltage - Supply
4.75 V ~ 5.25 V
Buck
Yes
Boost
No
Flyback
No
Inverting
No
Doubler
No
Divider
No
Cuk
No
Isolated
No
Operating Temperature
0°C ~ 70°C
Package / Case
32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
Frequency-max
4MHz
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6244CRZ
Manufacturer:
HARRIS
Quantity:
24
COMPENSATION WITHOUT LOAD-LINE REGULATION
The non load-line regulated converter is accurately modeled
as a voltage-mode regulator with two poles at the L-C
resonant frequency and a zero at the ESR frequency. A type
III controller, as shown in Figure 26, provides the necessary
compensation.
The first step is to choose the desired bandwidth, f
compensated system. Choose a frequency high enough to
assure adequate transient performance but not higher than 1/3
of the switching frequency. The type-III compensator has an
extra high-frequency pole, f
noise rejection or to assure adequate attenuation at the error-
amplifier high-order pole and zero frequencies. A good general
rule is to chose f
Choosing f
too much phase shift below the system bandwidth.
In the solutions to the compensation equations, there is a
single degree of freedom. For the solutions presented in
Equations 25, R
compensation components are then selected according to
Equations 25.
C
C
R
C
In Equations 25, L is the per-channel filter inductance
divided by the number of active channels; C is the sum total
of all output capacitors; ESR is the equivalent-series
resistance of the bulk output-filter capacitance; and V
the peak-to-peak sawtooth signal amplitude as described in
Figure 16 and Electrical Specifications.
Output Filter Design
The output inductors and the output capacitor bank together
form a low-pass filter responsible for smoothing the pulsating
voltage at the phase nodes. The output filter also must
provide the transient energy during the interval of time after
the beginning of the transient until the regulator can
respond. Because it has a low bandwidth compared to the
R
1
2
C
C
1
=
=
=
=
=
---------------------------------------- -
------------------------------------------------------------------ -
(
R
-------------------------------------------------------------------- -
0.75 V
------------------------------------------------------------------ -
(
2π
0.75V
2π
V
LC C ESR
FB
PP
)
)
2
2
HF
---------------------------------------- -
–
R
f
f
0
IN
LC C ESR
0
2π
FB
IN
f
f
0.75V
HF
C ESR
(
to be lower than 10f
HF
2πf
–
(
2πf
2
HF
FB
f
0
LCR
LCR
HF
(
f
HF
= 10f
)
IN
HF
is selected arbitrarily. The remaining
)
LCR
FB
LC 1
FB
LC 1
)
0
V
V
, but it can be higher if desired.
–
–
PP
HF
FB
PP
. This pole can be used for added
20
0
can cause problems with
0
, of the
(EQ. 25)
PP
is
ISL6244
switching frequency, the output filter necessarily limits the
system transient response leaving the output capacitor bank
to supply or sink load current while the current in the output
inductors increases or decreases to meet the demand.
In high-speed converters, the output capacitor bank is
usually the most costly (and often the largest) part of the
circuit. Output filter design begins with minimizing the cost of
this part of the circuit. The critical load parameters in
choosing the output capacitors are the maximum size of the
load step, ∆I; the load-current slew rate, di/dt; and the
maximum allowable output-voltage deviation under transient
loading, ∆V
their capacitance, ESR, and ESL (equivalent series
inductance).
At the beginning of the load transient, the output capacitors
supply all of the transient current. The output voltage will
initially deviate by an amount approximated by the voltage
drop across the ESL. As the load current increases, the
voltage drop across the ESR increases linearly until the
load current reaches its final value. The capacitors selected
must have sufficiently low ESL and ESR so that the total
output-voltage deviation is less than the allowable
maximum. Neglecting the contribution of inductor current
and regulator response, the output voltage initially deviates
by an amount
The filter capacitor must have sufficiently low ESL and ESR
so that ∆V < ∆V
Most capacitor solutions rely on a mixture of high-frequency
capacitors with relatively low capacitance in combination
with bulk capacitors having high capacitance but limited
high-frequency performance. Minimizing the ESL of the
high-frequency capacitors allows them to support the output
voltage as the current increases. Minimizing the ESR of the
bulk capacitors allows them to supply the increased current
with less output voltage deviation.
The ESR of the bulk capacitors also creates the majority of
the output-voltage ripple. As the bulk capacitors sink and
source the inductor ac ripple current (see Interleaving and
Equation 2), a voltage develops across the bulk-capacitor
ESR equal to I
are selected, the maximum allowable ripple voltage,
V
∆V
L
PP(MAX)
≥
≈
(
(
ESR
ESL
)
, determines the lower limit on the inductance.
)
----------------------------------------------------------- -
---- -
dt
di
MAX
V
IN
+
f
S
C,PP
(
V
. Capacitors are characterized according to
MAX
–
ESR
IN
N V
V
(ESR). Thus, once the output capacitors
.
OUT
PP MAX
) ∆I
(
V
OUT
)
December 28, 2004
(EQ. 26)
(EQ. 27)
FN9106.3