FAN5059MX Fairchild Semiconductor, FAN5059MX Datasheet - Page 15
![IC CTRLR DC/DC PROG SYNC 24SOIC](/photos/6/83/68326/261-24-soicw_sml.jpg)
FAN5059MX
Manufacturer Part Number
FAN5059MX
Description
IC CTRLR DC/DC PROG SYNC 24SOIC
Manufacturer
Fairchild Semiconductor
Datasheet
1.FAN5059MX.pdf
(18 pages)
Specifications of FAN5059MX
Applications
Controller, VRM8.5
Voltage - Input
5V
Number Of Outputs
1
Voltage - Output
1.3 ~ 3.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (7.5mm Width)
Output Current
18 A
Input Voltage
5 V
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
FAN5059MXTR
FAN5059MX_NL
FAN5059MX_NLTR
FAN5059MX_NLTR
FAN5059MX_NL
FAN5059MX_NLTR
FAN5059MX_NLTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FAN5059MX
Manufacturer:
MITEL
Quantity:
500
Part Number:
FAN5059MX
Manufacturer:
FAIRCHILD/仙童
Quantity:
20 000
PRODUCT SPECIFICATION
Programmable Active Droop
The FAN5059 includes Programmable Active Droop
the output current increases, the output voltage drops, and
the amount of this drop is user adjustable. This is done in
order to allow maximum headroom for transient response of
the converter. The current is typically sensed by measuring
the voltage across the R
ing its on time, as shown in Figure 1.
To program the amount of droop, use the formula
where I
is the resistance of the current sensor, either the source resistor
or the high-side MOSFET’s on-resistance. For example, to
get 30mV of droop with a maximum output current of 12.5A
and a 10m sense resistor, use R
(30mV * 18) = 3.33K . Further details on use of the
Programmable Active Droop
Bulletin AB-24.
Remote Sense
The FAN5059 offers remote sense of the output voltage to
minimize the output capacitor requirements of the converter.
It is highly recommended that the remote sense pin, Pin 20,
be tied directly to the processor power pins, so that the
effects of power plane impedance are eliminated. Further
details on use of the remote sense feature of the FAN5059
may be found in Applications Bulletin AB-24.
Adjusting the Linear Regulators’ Output Voltages
Any or all of the linear regulators’ outputs may be adjusted
high to compensate for voltage drop along traces, as shown
in Figure 6.
The resistor value should be chosen as
Note: See Note 4 in Electrical Specifications Table.
For example, to get the V
1.50V, use R = 10K * [(1.55/1.50) – 1] = 333 .
REV. 1.0.4 8/14/03
Figure 6. Adjusting the Output Voltage of the Linear
max
is the current at which the droop occurs, and R
VGATE
R
D
VFB
R
=
14.4K
10K *
DS,on
Regulator
TT
R
voltage to be 1.55V instead of
V
™
of the high-side MOSFET dur-
Droop
*I
may be found in Applications
D
10K
max
V
= 14.4K * 12.5A * 10m /
V
nom
out
*18
*R
™
–1
sense
VOUT
™
: as
sense
Using the FAN5059 for Vnorthbridge = 1.8V
In some motherboards, Intel requires that the AGP power can not
be greater than 2.2V while the chipset voltage (Vnorthbridge =
1.8V) is less than 1.0V. The FAN5059 can accomplish this by
using the VTT regulator to generate Vnorthbridge. Use the circuit
in Figure 6 with R = 2K . Since the linear regulators on the
FAN5059 all rise proportionally to one another, when Vnorth-
bridge = 1.0V, Vagp = 1.8V, meeting the Intel requirement.
PCB Layout Guidelines
• Placement of the MOSFETs relative to the FAN5059 is
• In general, all of the noisy switching lines should be kept
• Place the 0.1µF decoupling capacitors as close to the
• Each VCC and GND pin should have its own via to the
• Place the MOSFETs, inductor, and Schottky as close
• Place the output bulk capacitors as close to the CPU as
• A PC Board Layout Checklist is available from Fairchild
Additional Information
For additional information contact Fairchild Semiconductor at
http://www.fairchildsemi.com/cf/tsg.htm or contact an autho-
rized representative in your area.
critical. Place the MOSFETs such that the trace length of
the HIDRV and LODRV pins of the FAN5059 to the FET
gates is minimized. A long lead length on these pins will
cause high amounts of ringing due to the inductance of the
trace and the gate capacitance of the FET. This noise radiates
throughout the board, and, because it is switching at such
a high voltage and frequency, it is very difficult to suppress.
away from the quiet analog section of the FAN5059. That
is, traces that connect to pins 1, 2, 23, and 24 (HIDRV, SW,
LODRV and VCCP) should be kept far away from the
traces that connect to pins 3, 20 and 21.
FAN5059 pins as possible. Extra lead length on these
reduces their ability to suppress noise.
appropriate plane. This helps provide isolation between pins.
together as possible for the same reasons as in the first
bullet above. Place the input bulk capacitors as close to
the drains of the high side MOSFETs as possible. In
addition, placement of a 0.1µF decoupling cap right on the
drain of each high side MOSFET helps to suppress some
of the high frequency switching noise on the input of the
DC-DC converter.
possible to optimize their ability to supply instantaneous
current to the load in the event of a current transient.
Additional space between the output capacitors and the
CPU will allow the parasitic resistance of the board traces
to degrade the DC-DC converter’s performance under
severe load transient conditions, causing higher voltage
deviation. For more detailed information regarding
capacitor placement, refer to Application Bulletin AB-5.
Applications. Ask for Application Bulletin AB-11.
FAN5059
15