PM6680 STMicroelectronics, PM6680 Datasheet - Page 44

IC CTRLR DUAL STEP DOWN 32VFQFPN

PM6680

Manufacturer Part Number
PM6680
Description
IC CTRLR DUAL STEP DOWN 32VFQFPN
Manufacturer
STMicroelectronics
Datasheet

Specifications of PM6680

Applications
Controller, Notebook Power System
Voltage - Input
6 ~ 28 V
Number Of Outputs
2
Voltage - Output
0.9 ~ 5.5 V
Operating Temperature
0°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
32-VFQFN, 32-VFQFPN
Output Voltage
5 V, 0.9 V to 5.5 V, 0.9 V to 3.3 V
Output Current
0.33 A
Input Voltage
5.5 V to 28 V
Mounting Style
SMD/SMT
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 10 C
For Use With
497-6379 - BOARD EVALUATION FOR PM6680A497-6378 - BOARD EVALUATION FOR PM6680497-6425 - BOARD EVAL BASED ON PM6680A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PM6680
Manufacturer:
STMicroelectronics
Quantity:
135
Part Number:
PM6680
Manufacturer:
INFIONEON
Quantity:
1
Part Number:
PM6680
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
PM6680
Manufacturer:
ST
0
Part Number:
PM6680######
Manufacturer:
ST
0
Part Number:
PM6680A
Manufacturer:
ST
Quantity:
3 000
Part Number:
PM6680A
Manufacturer:
ST
0
Part Number:
PM6680ATR
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
PM6680TR
Manufacturer:
st
Quantity:
1 050
Device description
44/49
Figure 41. Current paths, ground connection and driver traces layout
possible. Place the synchronous diode D near the LS MOSFET. Connect the LS
MOSFET drain to the switching node with a short trace.
Place input capacitors near HS MOSFET drain. It is recommended to use the same
input voltage plan for both the switching sections, in order to put together all input
capacitors.
Place all the sensitive analog signals (feedbacks, voltage reference, current sense
paths) on the bottom side of the board or in an inner layer. Isolate them from the power
top side with a signal ground layer, SGND. Connect the SGND and PGND plans only in
one point (a multiple vias connection is preferable to a 0 ohm resistor connection) near
the PGND device pin. Place the device on the top or on the bottom size and connect
the exposed pad and the SGND pins to the SGND plan (see
As general rule, make the high side and low side drivers traces wide and short. The
high side driver is powered by the bootstrap circuit. It's very important to place
capacitor CBOOT and diode DBOOT as near as possible to the HGATE pin (for
example on the layer opposite to the device). Route HGATE and PHASE traces as near
as possible in order to minimize the area between them.
The Low side gate driver is powered by the 5V linear regulator output. Placing PGND
and LGATE pins near the low side MOSFETs reduces the length of the traces and the
crosstalk noise between the two sections.
The linear regulator output LDO5 is referred to SGND as long as the reference voltage
Vref. Place their output filtering capacitors as near as possible to the device.
Place input filtering capacitors near VCC and VIN pins.
It would be better if the feedback networks connected to COMP, FB and OUT pins are
"referred" to S
GND
in the same point as reference voltage V
ref
Figure 41
. To avoid capacitive
).
PM6680

Related parts for PM6680