ISL6217CVZ Intersil, ISL6217CVZ Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6217CVZ
Manufacturer Part Number
ISL6217CVZ
Description
IC CTRLR PWM INTEL PENT 38-TSSOP
Manufacturer
Intersil
Datasheet
1.ISL6217CVZ.pdf
(19 pages)
Specifications of ISL6217CVZ
Applications
Controller, Intel Pentium® IMVP-IV, IMVP+
Voltage - Input
5.5 ~ 25 V
Number Of Outputs
1
Operating Temperature
-10°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
38-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6217CVZ
Manufacturer:
Intersil
Quantity:
1 000
Company:
Part Number:
ISL6217CVZ
Manufacturer:
INTERSIL
Quantity:
485
Part Number:
ISL6217CVZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6217CVZ-T
Manufacturer:
INTER
Quantity:
2 500
Company:
Part Number:
ISL6217CVZ-T
Manufacturer:
NS
Quantity:
2 500
Functional Pin Description
VDD - This pin is used to connect +5V to the IC to supply
all power necessary to operate the chip. The IC starts to
operate when the voltage on this pin exceeds the rising
POR threshold and shuts down when the voltage on this
pin drops below the falling POR threshold.
VDDP - This pin provides a low-esr bypass connection to
the internal gate drivers for the +5V source.
PGOOD - This pin is used as an input and an output and is
tied to the Vccp and Vcc_mch PGOOD signals. During
start-up, this pin is recognized as an input and prevents
further slewing of the output voltage from the “Boot” level
until PGOOD from Vccp and Vcc_mch is enabled High.
After start-up, this pin has an open drain output used to
indicate the status of the CORE output voltage. This pin is
pulled low when the system output is outside of the
regulation limits. PGOOD includes a timer for power-on
delay.
EN - This pin is connected to the system signal VR_ON
and provides the enable/disable function for the PWM
controller.
PWRCH - This pin selects the number of power channels.
A HIGH logic level on this pin enables 2 channel operation,
and a LOW logic signal enables single channel operation.
OCSET - A resistor from this pin to ground sets the
overcurrent protection threshold.
VSEN - This pin is used for remote sensing of the
microprocessor CORE voltage.
DACOUT
PWRCH
PGOOD
DRSEN
DSEN#
COMP
SOFT
FSET
VID0
VID1
VID2
VID3
VID4
VID5
VDD
DSV
EA+
EN
FB
10
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
ISL6217
TSSOP
7
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
VBAT
ISEN1
PHASE1
UG1
BOOT1
VSSP1
LG1
VDDP
LG2
VSSP2
BOOT2
UG2
PHASE2
ISEN2
VSEN
DRSV
STV
OCSET
VSS
ISL6217
COMP - This pin provides connection to the error amplifier
output.
FB - This pin is connected to the inverting input of the error
amplifier.
EA+ - This pin is connected to the non-inverting input of the
error amplifier and is used for setting the “Droop” voltage.
STV - The voltage on this pin sets the initial start-up or
“Boot” voltage.
SOFT - This pin programs the slew rate of VID changes,
Deep Sleep and Deeper Sleep transitions and soft-start
after initializing. This pin is connected to ground via a
capacitor, and to EA+ through an external “Droop” resistor.
DSEN# - This pin connects to system logic “STP_CPU#”
and enables Deep Sleep mode of operation. Deep Sleep is
enabled when a logic LOW signal is detected on this pin.
DRSEN - This pin connects to system logic “DPRSLPVR”
and enables Deeper Sleep mode of operation when a logic
HIGH is detected on this pin.
VBAT - Voltage on this pin provides feed-forward battery
information which adjusts the oscillator ramp amplitude.
FSET - A resistor from this pin to ground programs the
switching frequency.
ISEN1, ISEN2 - These pins are used as current sense
inputs from the individual converter channel phase nodes.
DACOUT - This pin provides access to the output of the
Digital-to-Analog Converter.
DSV - The voltage on this pin provides the setpoint for
output voltage during Deep Sleep Mode of operation.
DRSV – The voltage on this pin provides the setpoint for
output voltage during Deeper Sleep Mode of operation.
VID0, VID1, VID2, VID3, VID4, VID5 - These pins are used
as inputs to the 6-bit Digital-to-Analog converter (DAC).
VID0 is the least significant bit and VID5 is the most
significant bit.
UG1, UG2 - These pins are the gate-drive outputs to the
high side MOSFETs for channels 1 and 2, respectively.
LG1, LG2 - These pins are the gate-drive outputs to the
low side MOSFETs for channels 1 and 2, respectively.
BOOT1, BOOT2 - These pins are connected to the
bootstrap capacitors, for upper gate-drive, for channels 1
and 2, respectively.
PHASE1, PHASE2 - These pins are connected to the
phase nodes of channels 1 and 2, respectively.
VSSP1, VSSP2 - These pins are connected to the power
ground of channels 1 and 2, respectively.
VSS - This pin provides connection for signal ground.