ISL6217CVZ Intersil, ISL6217CVZ Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6217CVZ
Manufacturer Part Number
ISL6217CVZ
Description
IC CTRLR PWM INTEL PENT 38-TSSOP
Manufacturer
Intersil
Datasheet
1.ISL6217CVZ.pdf
(19 pages)
Specifications of ISL6217CVZ
Applications
Controller, Intel Pentium® IMVP-IV, IMVP+
Voltage - Input
5.5 ~ 25 V
Number Of Outputs
1
Operating Temperature
-10°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
38-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6217CVZ
Manufacturer:
Intersil
Quantity:
1 000
Company:
Part Number:
ISL6217CVZ
Manufacturer:
INTERSIL
Quantity:
485
Part Number:
ISL6217CVZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6217CVZ-T
Manufacturer:
INTER
Quantity:
2 500
Company:
Part Number:
ISL6217CVZ-T
Manufacturer:
NS
Quantity:
2 500
Operation
Initialization
Once the +5VDC supply voltage, as connected to the
ISL6217 VDD pin, reaches the Power-On Reset (POR)
rising threshold, the PWM drive signals are held in “high-
impedance state” or high impedance mode. This results in
both high and low side MOSFETs being held low. Once the
supply voltage exceeds the POR rising threshold, the
controller will respond to a logic level high on the EN pin
and initiate the soft-start interval. If the supply voltage
drops below the POR falling threshold, POR shutdown is
triggered and the PWM signals are again driven to “high-
impedance state”.
The system signal, VR_ON is directly connected to the EN
pin of the ISL6217. Once the voltage on the EN pin rises
above 2.0V, the chip is enabled and soft-start begins. The
EN pin of the ISL6217 is also used to reset the ISL6217, for
cases when an undervoltage or overcurrent fault condition
has latched the IC off. A toggling of the state of this pin to a
level below 1.0V will re-enable the IC. For the case of an
overvoltage fault, the VDD pin must be reset.
During start-up, the ISL6217 regulates to the voltage on the
STV pin. This is referred to as the “Boot” voltage and is
labeled VBOOT in Figure 2. Once power good signals are
received from the Vccp and Vcc_mch regulators, the
ISL6217 will capture the VID code and regulate to this
command voltage within 3ms to 12ms. The PGOOD pin of
the ISL6217 is both an input and an output and is further
described in the “Fault Protection” section of this document.
Soft-Start Interval
Once VDD rises above the POR rising threshold and the
PGOOD
PGOOD
VID
V
VR_ON / EN
CC-CORE
FIGURE 2.
Vccp / Vcc_mch
Vcc_core
TIMING DIAGRAM SHOWING VR_ON, VCC_CORE AND PGOOD FOR VCC_CORE, VCCP AND VCC_MCH
-12%
8
< 3ms
t1
>10us
ISL6217
Capture VID Code
EN pin voltage is above the threshold of 2.0V, a soft-start
interval is initiated (Refer to Figures 2 and 3).
The voltage on the EA+ pin is the reference voltage for the
regulator. The voltage on the EA+ pin is equal to the
voltage on the SOFT pin minus the “Droop” resistor
voltage, V DROOP . During start-up, when the voltage on
SOFT is less than the “Boot” voltage V BOOT , a small 30µA
current source, I1, is used to slowly ramp up the voltage on
the soft-start Capacitor C SOFT . This slowly ramps up the
reference voltage for the controller, and therefore, controls
the slew rate of the output voltage. The STV pin is
externally programmable and sets the start-up, or “Boot”
voltage, V BOOT . The programming of this voltage level is
explained in the “STV, DSV and DRSV” section of this
document.
The ISL6217 PGOOD pin is both an input and an output.
The system signal, IMVP4_PWRGD, is connected to power
good signals from the Vccp and Vcc_mch supplies. The
Intersil ISL6227, Dual Voltage Regulator is an ideal choice
for the Vccp and Vcc_mch supplies.
Once the output voltage is within the “Boot” level regulation
limits and a logic high PGOOD signal from the Vccp and
Vccp_mch regulators is received, the ISL6217 is enabled to
capture the VID code and regulate to that command
voltage (Refer to Figure 2 and Figure 3). A second current
source, I2, is added to I1, after the initial start-up transition.
I2 is approximately 100µA, and raises the total SOFT pin
sinking and sourcing current to 130µA. This increased
current is used to increase the slew rate of the reference to
meet all Active, Deep and Deeper Sleep slew rate
requirements of the Intel IMVP-IV™ and IMVP-IV+™
specification.
3ms to 12ms
t2
V
BOOT
V
VID