ISL6261CRZ Intersil, ISL6261CRZ Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6261CRZ
Manufacturer Part Number
ISL6261CRZ
Description
IC CTRLR BUCK 1PHASE 40-MLFP
Manufacturer
Intersil
Datasheet
1.ISL6261CR7Z.pdf
(34 pages)
Specifications of ISL6261CRZ
Applications
Converter, Intel IMVP-6
Voltage - Input
5 ~ 21 V
Number Of Outputs
1
Voltage - Output
0.3 ~ 1.5 V
Operating Temperature
-10°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
40-VFQFN, 40-VFQFPN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6261CRZ
Manufacturer:
INTERSIL
Quantity:
8 831
Company:
Part Number:
ISL6261CRZ-T
Manufacturer:
SAWNICS
Quantity:
10 623
Part Number:
ISL6261CRZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
High Efficiency Operation Mode
The operational modes of the ISL6261 depend on the
control signal states of DPRSTP#, FDE, and DPRSLPVR, as
shown in Table 2. These control signals can be tied to lntel
IMVP-6
configuration for all IMVP-6
DPRSTP# = 0, FDE = 0 and DPRSLPVR = 1 enables the
ISL6261 to operate in diode emulation mode (DEM) by
monitoring the low-side FET current. In diode emulation
mode, when the low-side FET current flows from source to
drain, it turns on as a synchronous FET to reduce the
conduction loss. When the current reverses its direction
trying to flow from drain to source, the ISL6261 turns off the
low-side FET to prevent the output capacitor from
discharging through the inductor, therefore eliminating the
extra conduction loss. When DEM is enabled, the regulator
works in automatic discontinuous conduction mode (DCM),
meaning that the regulator operates in CCM in heavy load,
and operates in DCM in light load. DCM in light load
decreases the switching frequency to increase efficiency.
This mode can be used to support the deeper sleep mode of
the microprocessor.
DPRSTP# = 0 and FDE = 1 enables the enhanced diode
emulation mode (EDEM), which increases the VW-COMP
window voltage by 33%. This further decreases the
switching frequency at light load to boost efficiency in the
deeper sleep mode.
For other combinations of DPRSTP#, FDE, and
DPRSLPVR, the ISL6261 operates in forced CCM.
The ISL6261 operational modes can be set according to
CPU mode signals to achieve the best performance. There
are two options: (1) Tie FDE to DPRSLPVR, and tie
DPRSTP# and DPRSLPVR to the corresponding CPU mode
signals. This configuration enables EDEM in deeper sleep
mode to increase efficiency. (2) Tie FDE to “1” and
DPRSTP# to “0” permanently, and tie DPRSLPVR to the
corresponding CPU mode signal. This configuration sets the
regulator in EDEM all the time. The regulator will enter DCM
Overcurrent fault
Way-Overcurrent fault
Overvoltage fault (1.7V)
Overvoltage fault
(+200mV)
Undervoltage fault
(-300mV)
Over-temperature fault
(NTC<1.18)
FAULT TYPE
®
control signals to maintain the optimal system
120μs
< 2μs
Immediately
1ms
1ms
Immediately
FAULT DURATION PRIOR
®
14
conditions.
TO PROTECTION
TABLE 3. FAULT-PROTECTION SUMMARY OF ISL6261
PWM tri-state, PGOOD latched low
PWM tri-state, PGOOD latched low
Low-side FET on until Vcore < 0.85V, then PWM tri-
state, PGOOD latched low (OV-1.7V always)
PWM tri-state, PGOOD latched low
PWM tri-state, PGOOD latched low
VR_TT# goes high
®
ISL6261
PROTECTION ACTIONS
based on load current. Light-load efficiency is increased in
both active mode and deeper sleep mode.
CPU mode-transition sequences often occur in concert with
VID changes. The ISL6261 employs carefully designed
mode-transition timing to work in concert with the VID
changes.
The ISL6261 is equipped with internal counters to prevent
control signal glitches from triggering unintended mode
transitions. For example: Control signals lasting less than
seven switching periods will not enable the diode emulation
mode.
Dynamic Operation
The ISL6261 responds to VID changes by slewing to new
voltages with a dv/dt set by the SOFT capacitor and the logic
of DPRSLPVR. If C
output voltage will move at a maximum dv/dt of ±10mV/μs
for large changes. The maximum dv/dt can be used to
achieve fast recovery from Deeper Sleep to Active mode. If
C
move at a dv/dt of ±2mV/μs for large changes. The slow
dv/dt into and out of deeper sleep mode will minimize the
audible noise. As the output voltage approaches the VID
command value, the dv/dt moderates to prevent overshoot.
The ISL6261 is IMVP-6
DPRSLPVR logic.
Intersil R
High-speed input voltage transients have little effect on the
output voltage.
Intersil R
transients to achieve fast response. Upon load application,
the ISL6261 will transiently increase the switching frequency
to deliver energy to the output more quickly. Compared with
steady state operation, the PWM pulses during load
application are generated earlier, which effectively increases
the duty cycle and the response speed of the regulator.
Upon load release, the ILS6261 will transiently decrease the
switching frequency to effectively reduce the duty cycle to
achieve fast response.
SOFT
= 20nF and DPRSLPVR = 1, the output voltage will
3
3
™ has an intrinsic voltage feed forward function.
™ commands variable switching frequency during
SOFT
®
= 20nF and DPRSLPVR = 0, the
compliant for DPRSTP# and
VR_ON toggle or VDD toggle
VR_ON toggle or VDD toggle
VDD toggle
VR_ON toggle or VDD toggle
VR_ON toggle or VDD toggle
N/A
FAULT RESET
September 27, 2006
FN9251.1