L6712ADTR STMicroelectronics, L6712ADTR Datasheet - Page 5

• Manufacturer Part Number: L6712ADTR
• Description: IC CTRLR DC/DC 2PH SYNC 28SOIC
• Manufacturer: STMicroelectronics
• Type: Step-Down (Buck)r

Specifications of L6712ADTR

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 0.9 ~ 3.3 V
• Current - Output: 2A
• Frequency - Switching: 150kHz
• Voltage - Input: 12V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (7.5mm Width)
• Power - Output: 2W
• Operating Temperature Range: - 40 C to + 125 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 497-4218-2

Table 4. Electrical Characteristcs (continued)
(V
Note: 1. Output voltage is specified including Error Amplifier Offset in the trimming chain. Remote Amplifier is not included.
Table 5. Voltage Identification (VID) Codes.
Table 6. Pin Function
PROTECTIONS
CC
SO
1
2
3
4
5
6
7
8
9
V
PGOOD
Symbol
I
= 12V±10%, T
PGOODH
PGOODL
OVP
UVP
N. (*)
VID2
1
1
1
1
0
0
0
0
VFQFPN
5,6
33
34
35
36
2
4
7
8
Upper Threshold
Lower Threshold
Over Voltage Threshold
Under Voltage Trip
PGOOD Voltage Low
PGOOD Leakage
J
= 0°C to 70°C unless otherwise specified)
PHASE1
UGATE1
LGATE1
VCCDR
BOOT1
COMP
SGND
Name
Parameter
VCC
FB
VID1
1
1
0
0
1
1
0
0
Channel 1 LS driver output.
A little series resistor helps in reducing device-dissipated power.
LS drivers supply: it can be varied from 5V to 12V buses.
Filter locally with at least 1µF ceramic cap vs. PGND.
Channel 1 HS driver return path. It must be connected to the HS1 mosfet source
and provides the return path for the HS driver of channel 1.
Channel 1 HS driver output.
A little series resistor helps in reducing device-dissipated power.
Channel 1 HS driver supply. This pin supplies the relative high side driver.
Connect through a capacitor (100nF typ.) to the PHASE1 pin and through a diode
to VCC (cathode vs. boot).
Device supply voltage. The operative supply voltage is 12V ±10%.
Filter with 1µF (Typ.) capacitor vs. GND.
All the internal references are referred to this pin. Connect it to the PCB signal
ground.
This pin is connected to the error amplifier output and is used to compensate the
control feedback loop.
This pin is connected to the error amplifier inverting input and is used to
compensate the control feedback loop.
VSEN Rising
VSEN Falling
VSEN Rising
VSEN Falling
I
V
PGOOD
PGOOD
Test Condition
= -4mA
= 5V
VID0
1
0
1
0
1
0
1
0
Description
Min.
108
115
84
55
Output Voltage (V)
Ext. Ref.
Typ.
112
122
88
60
0.900
1.250
1.500
1.715
1.800
2.500
3.300
L6712A L6712
Max.
115
130
0.4
92
65
1
Unit
µA
%
%
%
%
V
5/29