LTC3868IUH#TRPBF Linear Technology, LTC3868IUH#TRPBF Datasheet - Page 20

• Manufacturer Part Number: LTC3868IUH#TRPBF
• Description: IC CTRLR STP-DN SYNC DUAL 32QFN
• Manufacturer: Linear Technology
• Series: PolyPhase®r
• Type: Step-Down (Buck)r

Specifications of LTC3868IUH#TRPBF

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 0.8 ~ 14 V
• Frequency - Switching: 50kHz ~ 900kHz
• Voltage - Input: 4 ~ 24 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Power - Output: -

LTC3868
large voltage transients, a low ESR capacitor sized for the
maximum RMS current of one channel must be used. The
maximum RMS capacitor current is given by:
Equation 1 has a maximum at V
= I
used for design because even signifi cant deviations do not
offer much relief. Note that capacitor manufacturers’ ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor, or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may be paralleled to meet
size or height requirements in the design. Due to the high
operating frequency of the LTC3868, ceramic capacitors
can also be used for C
if there is any question.
The benefi t of the LTC3868 2-phase operation can be calcu-
lated by using the Equation 1 for the higher power controller
and then calculating the loss that would have resulted if
both controller channels switched on at the same time.
The total RMS power lost is lower when both controllers
are operating due to the reduced overlap of current pulses
required through the input capacitor’s ESR. This is why
the input capacitor’s requirement calculated above for the
worst-case controller is adequate for the dual controller
design. Also, the input protection fuse resistance, battery
resistance, and PC board trace resistance losses are also
reduced due to the reduced peak currents in a 2-phase
system. The overall benefi t of a multiphase design will
only be fully realized when the source impedance of the
power supply/battery is included in the effi ciency testing.
The drains of the top MOSFETs should be placed within
1cm of each other and share a common C
the sources and C
current resonances at V
A small (0.1μF to 1μF) bypass capacitor between the chip
V
suggested. A 10Ω resistor placed between C
the V
channels.
20
APPLICATIONS INFORMATION
C
IN
IN
OUT
pin and ground, placed close to the LTC3868, is also
Required I
IN
/2. This simple worst-case condition is commonly
pin provides further isolation between the two
RMS
IN
may produce undesirable voltage and
≈
IN
I
MAX
. Always consult the manufacturer
V
IN
IN
.
⎡
⎣
(
V
OUT
IN
)
= 2V
(
V
IN
IN
OUT
– V
(s). Separating
, where I
OUT
IN
(C1) and
)
⎤
⎦
1/ 2
RMS
(1)
The selection of C
resistance (ESR). Typically, once the ESR requirement
is satisfi ed, the capacitance is adequate for fi ltering. The
output ripple (∆V
where f
capacitance and ∆I
The output ripple is highest at maximum input voltage
since ∆I
Setting Output Voltage
The LTC3868 output voltages are each set by an external
feedback resistor divider carefully placed across the out-
put, as shown in Figure 6. The regulated output voltage
is determined by:
To improve the frequency response, a feedforward ca-
pacitor, C
route the V
inductor or the SW line.
Soft-Start (SS Pins)
The start-up of each V
the respective SS pin. When the voltage on the SS pin is
less than the internal 0.8V reference, the LTC3868 regulates
the V
of 0.8V. The SS pin can be used to program an external
soft-start function.
ΔV
V
OUT
FB
OUT
O
pin voltage to the voltage on the SS pin instead
L
= 0.8V 1+
FF
is the operating frequency, C
increases with input voltage.
≈ ΔI
, may be used. Great care should be taken to
FB
line away from noise sources, such as the
Figure 6. Setting Output Voltage
L
1/2 LTC3868
⎛
⎜
⎝
⎛
⎜
⎝
OUT
ESR +
OUT
L
R
R
) is approximated by:
is the ripple current in the inductor.
V
B
OUT
A
FB
is driven by the effective series
⎞
⎟
⎠
8 • f • C
is controlled by the voltage on
V
1
OUT
OUT
R
R
3868 F06
B
A
⎞
⎟
⎠
C
OUT
FF
is the output
3868fd