HCPL-2212-000E Avago Technologies US Inc., HCPL-2212-000E Datasheet - Page 13
![OPTOCOUPLER LOGIC-OUT 5MBD 8-DIP](/photos/7/66/76618/516-8-dip_sml.jpg)
HCPL-2212-000E
Manufacturer Part Number
HCPL-2212-000E
Description
OPTOCOUPLER LOGIC-OUT 5MBD 8-DIP
Manufacturer
Avago Technologies US Inc.
Type
Logicr
Datasheet
1.HCPL-0201-500E.pdf
(18 pages)
Specifications of HCPL-2212-000E
Package / Case
8-DIP (0.300", 7.62mm)
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
25mA
Data Rate
5MBd
Propagation Delay High - Low @ If
150ns @ 3mA
Current - Dc Forward (if)
10mA
Input Type
DC
Output Type
Push-Pull, Totem-Pole
Mounting Type
Through Hole
Isolation Voltage
3750 Vrms
Maximum Continuous Output Current
25 mA
Maximum Fall Time
0.007 us
Maximum Forward Diode Current
10 mA
Output Device
Logic Gate Photo IC
Configuration
1 Channel
Maximum Baud Rate
5 MBd(Typ)
Maximum Forward Diode Voltage
1.7 V
Maximum Reverse Diode Voltage
5 V
Maximum Power Dissipation
210 mW
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Package Type
8-Pin DIP
No. Of Channels
1
Optocoupler Output Type
Logic Gate
Input Current
5mA
Output Voltage
20V
Opto Case Style
DIP
No. Of Pins
8
Common Mode Ratio
10K
Current Rating
5mA
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
516-1651-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-2212-000E
Manufacturer:
AVAGO
Quantity:
5 000
Part Number:
HCPL-2212-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Package Characteristics
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203
Notes:
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage
12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.
13
1. Each channel.
2. Derate total package power dissipation, P
3. Duration of output short circuit time should not exceed 10 ms.
4. For single devices, input capacitance is measured between pin 2 and pin 3.
5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
6. The t
7. CM
8. For HCPL-2202/12, V
9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
Withstand
Voltage
Parameter
Input-Output Momentary
Input-Output Resistance
Input-Output Capacitance
Input-Input Insulation
Leakage Current
Resistance (Input-Input)
Capacitance (Input-Input)
the output pulse. The t
trailing edge of the output pulse.
CM
detection current limit, I
EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
detection current limit, I
EN/DIN EN 60747-5-2 Insulation Characteristics Table.
H
L
is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, V
is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, V
PLH
*
propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of
HCNW22XX
HCNW22XX
HCNW22XX
O
is on pin 6.
PHL
I-O
I-O
propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the
≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
Sym.
V
R
C
R
C
I
ISO
I-I
I-O
I-O
I-I
I-I
T
, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.
3750
5000
Min.
10
10
12
11
0.005
0.25
Typ.
10
10
10
0.6
0.5
12
13
11
Max.
0.6
t = 5 s, V
V rms
Units
µA
pF
pF
Ω
Ω
I-I
= 500 V
RH < 50%, t = 1 min.
T
T
T
T
Relative Humidity = 45%,
V
f = 1 MHz
A
A
A
A
I-I
= 25°C
= 25°C
= 100°C
= 25°C, V
= 500 V
Test Conditions
I-O
= 0 Vdc
V
f = 1 MHz,
I-O
= 500 Vdc
Fig.
O
O
< 0.8 V.
5, 10
5, 11
> 2.0 V.
Note
12
12
12
5
5