HCPL-7710-000E Avago Technologies US Inc., HCPL-7710-000E Datasheet - Page 12

• Manufacturer Part Number: HCPL-7710-000E
• Description: OPTOCOUPLER CMOS 12MBD 8-DIP
• Manufacturer: Avago Technologies US Inc.
• Type: Logicr

Specifications of HCPL-7710-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 12.5MBd
• Propagation Delay High - Low @ If: 20ns
• Input Type: Logic
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 10 mA
• Maximum Fall Time: 0.008 us
• Maximum Forward Diode Current: 10 mA
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 12.5 MBd
• Maximum Power Dissipation: 150 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Package Type: 8-Pin DIP
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 10µA
• Output Voltage: 5V
• Opto Case Style: DIP
• No. Of Pins: 8
• Common Mode Ratio: 10000
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1480-5

12
Digital Field Bus Communication Networks
To date, despite its many drawbacks, the 4 - 20 mA
analog current loop has been the most widely accepted
standard for implementing process control systems.
In today’s manufacturing environment, however,
automated systems are expected to help manage
the process, not merely monitor it. With the advent
of digital field bus communication networks such as
DeviceNet, PROFIBUS, and Smart Distributed Systems
(SDS), gone are the days of constrained information.
Figure 17. Typical field bus communication physical model.
Optical Isolation for Field Bus Networks
To recognize the full benefits of these networks, each
recommends providing galvanic isolation using Avago
optocouplers. Since network communication is bi-direc-
tional (involving receiving data from and transmitting
data onto the network), two Avago optocouplers are
needed. By providing galvanic isolation, data integrity is
retained via noise reduction and the elimination of false
signals. In addition, the network receives maximum pro-
tection from power system faults and ground loops.
Within an isolated node, such as the DeviceNet Node
shown in Figure 18, some of the node’s components are
referenced to a ground other than V- of the network.
CONFIGURATION
TRANSCEIVER
INTERFACE
ISOLATION
OPTICAL
DEVICE
BUS
TRANSCEIVER
CONTROLLER
INTERFACE
ISOLATION
OPTICAL
BUS
TRANSCEIVER
INTERFACE
ISOLATION
STARTER
OPTICAL
MOTOR
BUS
HCPL-0710 fig 16
FIELD BUS
TRANSCEIVER
CONTROLLER
INTERFACE
ISOLATION
OPTICAL
XXXXXX
YYY
MOTOR
BUS
Controllers can now receive multiple readings from field
devices (sensors, actuators, etc.) in addition to diagnos-
tic information.
The physical model for each of these digital field bus
communication networks is very similar as shown in
Figure 17. Each includes one or more buses, an interface
unit, optical isolation, transceiver, and sensing and/or
actuating devices.
These components could include such things as devices
with serial ports, parallel ports, RS232 and RS485 type
ports. As shown in Figure 18, power from the network is
used only for the transceiver and input (network) side of
the optocouplers.
Isolation of nodes connected to any of the three types of
digital field bus networks is best achieved by using the
HCPL-x710 optocouplers. For each network, the HCPL-
x710 satisify the critical propagation delay and pulse
width distortion requirements over the temperature
range of 0°C to +85°C, and power supply voltage range
of 4.5 V to 5.5 V.
TRANSCEIVER
INTERFACE
ISOLATION
OPTICAL
BUS
SENSOR