ACPL-M60L-500E Avago Technologies US Inc., ACPL-M60L-500E Datasheet - Page 8

• Manufacturer Part Number: ACPL-M60L-500E
• Description: OPTOCOUPLER 15MBD 3.3V 5-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-M60L-500E

• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 50 mA
• Maximum Fall Time: 0.02 us
• Maximum Forward Diode Current: 20 mA
• Maximum Rise Time: 45 ns
• Minimum Forward Diode Voltage: 1.4 V
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 10 MBps
• Maximum Forward Diode Voltage: 1.85 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Power Dissipation: 85 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: SO-5
• Number Of Elements: 1
• Input Type: DC
• Output Type: Open Collector
• Forward Voltage: 1.75V
• Forward Current: 20mA
• Output Current: 50mA
• Package Type: SOIC
• Operating Temp Range: -40C to 85C
• Power Dissipation: 85mW
• Propagation Delay Time: 90ns
• Pin Count: 5
• Mounting: Surface Mount
• Reverse Breakdown Voltage: 5V
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Notes:
10. CM
11. For sinusoidal voltages, (|dV
12. Device considered a two terminal device: pins 1 and 3 shorted together, and pins 4, 5 and 6 shorted together.
13. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V
Figure 1. Typical high level output current vs. temperature.
8
Parameter
Logic High
Common
Mode
Transient
Immunity
Logic Low
Common
Mode
Transient
Immunity
1. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not
2. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not
3. Derate linearly above +80˚C free-air temperature at a rate of 2.7 mW/˚C for the SOIC-5 package.
4. Bypassing of the power supply line is required, with a 0.1 µF ceramic disc capacitor adjacent to each optocoupler as illustrated in
5. The t
6. The t
7. t
8. See test circuit for measurement details.
9. CM
detection current limit, I
exceed 20 mA.
exceed 15 mA.
Figure 11. Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm.
of the output pulse.
of the output pulse.
test conditions.
(i.e., V
(i.e., V
PSK
15
15
10
10
5
5
0
0
-60
-60
H
L
is equal to the worst case difference in t
is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state
PLH
PHL
is the maximum tolerable rate of rise on the common mode voltage to assure that the output will remain in a high logic state
o
o
> 2.0 V).
< 0.8 V).
-40
-40
propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge
propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge
-20
-20
T
A
Sym.
|CM
|CM
– TEMPERATURE – C
0
0
H
L
|
|
20
20
I-O
Device
ACPL-M60L
ACPL-M60L
40
40
≤ 5 µA).
CM
V
V
V
V
I
I
F
F
CC
CC
O
O
= 250 µA
= 250 µA
60
60
= 3.3 V
= 3.3 V
| / dt)
= 3.3 V
= 3.3 V
80
80
max
100
100
= πf
Min.
15,000
10,000
15,000
10,000
PHL
CM
V
and/or t
CM
15
10
Typ.
25,000
15,000
25,000
15,000
(p-p).
5
0
-60
PLH
-40
that will be seen between units at any given temperature and specified
-20
Units
V/µs
V/µs
T
A
- TEMPERATURE -
0
20
Test Conditions
|V
|V
CM
CM
4 0
V
V
I
| = 1000 V
| = 1000 V
F
CC
O
= 250 µA
60
°
= 5.5 V
C
= 5.5 V
8 0
100
V
V
R
V
V
R
V
V
R
V
V
R
CC
O(MIN)
L
CC
O(MIN)
L
CC
O(MAX)
L
CC
O(MIN)
L
= 350 Ω, T
= 350 Ω, T
= 350 Ω, T
= 350 Ω, T
= 3.3 V, I
= 5 V, I
= 3.3 V, I
= 5 V, I
= 2 V,
= 2 V,
= 0.8 V,
= 0.8 V,
F
F
= 0 mA,
= 7.5 mA,
F
F
A
A
A
A
= 0 mA,
= 7.5 mA,
= 25˚C
= 25˚C
= 25˚C
= 25˚C
RMS
for 1 second (Leakage
Fig.
9
9
9
9
Note
9, 11
9, 11
10, 11
10, 11