TLP2601 Toshiba, TLP2601 Datasheet - Page 8

• Manufacturer Part Number: TLP2601
• Description: PHOTOCOUPLER HS LOGIC OUT 8-DIP
• Manufacturer: Toshiba

Specifications of TLP2601

• Voltage - Isolation: 2500Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 25mA
• Data Rate: 10MBd
• Propagation Delay High - Low @ If: 60ns @ 7.5mA
• Current - Dc Forward (if): 20mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• No. Of Channels: 1
• Isolation Voltage: 2.5kV
• Optocoupler Output Type: Transistor
• Input Current: 20mA
• Output Voltage: 5.5V
• Opto Case Style: DIP
• No. Of Pins: 8
• Approval Bodies: UL
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Notes
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11. Enable
either a ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected
as close as possible to the package V
t
t
t
t
t
t
CM
CM
input
The V
pHL
pLH
f
r
EHL
ELH
L
H
CC
supply voltage to each TLP2601 isolator must be bypassed by a 0.1μF capacitor of larger.This can be
･
･
･
･
･
･
･
･
･
･
Propagation delay is measured from the 3.75mA level on the low to high transition of the input
current pulse to the 1.5V level on the high to low transition of the output voltage pulse.
Propagation delay is measured from the 3.75mA level on the high to low transition of the input
current pulse to the 1.5V level on the low to high transition of the output voltage pulse.
Fall time is measured from the 10% to the 90% levels of the high to low transition on the output
pulse.
Rise time is measured from the 90% to 10% levels of the low to high transition on the output
pulse.
Enable input propagation delay is measured from the 1.5V level on the low to high transition of
the input voltage pulse to the 1.5V level on the high to low transition of the output voltage pulse.
Enable input propagation delay is measured from the 1.5V level on the high to low transition of
the input voltage pulse to the 1.5V level on the low to high transition of the output voltage pulse.
The maximum tolerable rate of fall of the common mode voltage to ensure the output will remain
in the low output state (i.e., V
Measured in volts per microsecond (V / μs).
The maximum tolerable rate of fall of the common mode voltage to ensure the output will remain
in the high state (i.e., V
Measured in volts per microsecond(V / μs).
Volts/microsecond can be translated to sinusoidal voltages:
Example:
V
minimum.
Device considered a two−terminal device: Pins 1, 2, 3 and 4 shorted together, and Pins 5, 6, 7 and
8 shorted together.
No pull up resistor required as the device has an internal pull up resistor.
CM
= 318V
V / μs =
pp
when f
(dv
CM
dt
CM
CC
OUT
)
= 1MHz using CM
Max.
and GND pins of each device.
> 2.0V).
OUT
= f
< 0.8V).
CM
V
8
CM
(p.p.)
L
and CM
H
= 1000V / μs data sheet specified
2007-10-01
TLP2601