MT16VDDF12864HG-335D2 Micron Technology Inc, MT16VDDF12864HG-335D2 Datasheet - Page 19
![MODULE DDR SDRAM 1GB 200-SODIMM](/photos/7/83/78380/mt16vddf12864hg-335d2_sml.jpg)
MT16VDDF12864HG-335D2
Manufacturer Part Number
MT16VDDF12864HG-335D2
Description
MODULE DDR SDRAM 1GB 200-SODIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT16VDDF12864HY-335F2.pdf
(30 pages)
Specifications of MT16VDDF12864HG-335D2
Memory Type
DDR SDRAM
Memory Size
1GB
Speed
167MHz
Package / Case
200-SODIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
557-1109
pdf: 09005aef80a77a90, source: 09005aef80a646bc
DDF16C64_128x64HG.fm - Rev. D 9/04 EN
22. The valid data window is derived by achieving
23. Each byte lane has a corresponding DQS.
24. This limit is actually a nominal value and does not
25. To maintain a valid level, the transitioning edge of
the DRAM controller greater than eight refresh
cycles is not allowed.
other specifications:
(
directly porportional with the clock duty cycle
and a practical data valid window can be derived.
The clock is allowed a maximum duty cycle varia-
tion of 45/55, beyond which functionality is
uncertain. Figure 8, Derating Data Valid Window,
shows derating curves for duty cycles ranging
between 50/50 and 45/55.
result in a fail value. CKE is HIGH during
REFRESH command period (
CKE is LOW (i.e., during standby).
the input must:
a. Sustain a constant slew rate from the current
b. Reach at least the target AC level.
t
QH =
3.8
3.6
3.4
3.2
3.0
2.8
2.6
2.4
2.2
2.0
1.8
AC level through to the target AC level, V
or V
t
IH
HP -
50/50
3.750
(AC).
2.500
t
QHS). The data valid window derates
NA
49.5/50.5
3.700
-335
-262/-26A/-265 @
-262/-26A/-265 @
2.463
t
HP (
t
Figure 8: Derating Data Valid Window
CK/2),
3.650
49/51
2.425
t
t
CK = 10ns
CK = 7.5ns
t
RFC [MIN]) else
t
DQSQ, and
48.5/52.5
3.600
2.388
IL
(AC)
48/52
3.550
t
QH
2.350
Clock Duty Cycle
19
47.5/53.5
3.500
26. JEDEC specifies CK and CK# input slew rate must
27. DQ and DM input slew rates must not deviate
28. V
29. The clock is allowed up to ±150ps of jitter. Each
30.
31. READs and WRITEs with auto precharge are not
2.313
be 1V/ns (2V/ns differentially).
from DQS by more than 10 percent. If the DQ/
DM/DQS slew rate is less than 0.5V/ns, timing
must be derated: 50ps must be added to
t
slew rate exceeds 4V/ns, functionality is uncer-
tain. For -335, slew rates must be 0.5 V/ns.
not active while any bank is active.
timing parameter is allowed to vary by the same
amount.
t
minimum actually applied to the device CK and
CK# inputs, collectively during bank active.
allowed to be issued until
fied prior to the internal precharge command
being issued.
c. After the AC target level is reached, continue to
DH for each 100mv/ns reduction in slew rate. If
HP min is the lesser of
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD
maintain at least the target DC level, V
or V
47/53
3.450
must not vary more than 4 percent if CKE is
2.275
IH
(DC).
46.5/54.5
200-PIN DDR SODIMM
512MB, 1GB (x64, DR)
3.400
2.238
3.350
46/54
2.200
t
t
CL minimum and
RAS(MIN) can be satis-
45.5/55.5
3.300
2.163
©2004 Micron Technology, Inc.
3.250
45/55
t
DS and
2.125
IL
(DC)
t
CH