MT16VDDF12864HG-335D2 Micron Technology Inc, MT16VDDF12864HG-335D2 Datasheet - Page 4
![MODULE DDR SDRAM 1GB 200-SODIMM](/photos/7/83/78380/mt16vddf12864hg-335d2_sml.jpg)
MT16VDDF12864HG-335D2
Manufacturer Part Number
MT16VDDF12864HG-335D2
Description
MODULE DDR SDRAM 1GB 200-SODIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT16VDDF12864HY-335F2.pdf
(30 pages)
Specifications of MT16VDDF12864HG-335D2
Memory Type
DDR SDRAM
Memory Size
1GB
Speed
167MHz
Package / Case
200-SODIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
557-1109
Table 5:
Pin numbers may not correlate with symbols; refer to Pin Assignment tables on page 3 for more information
pdf: 09005aef80a77a90, source: 09005aef80a646bc
DDF16C64_128x64HG.fm - Rev. D 9/04 EN
107, 108, 109, 110, 111, 112,
12, 26, 48, 62, 134, 148, 170,
11, 25, 47, 61, 133, 147, 169,
99, 100, 101, 102, 105,106,
35, 37, 158, 160
PIN NUMBERS
118, 119, 120
194, 196, 198
121, 122
116, 117
95, 96
115
195
193
184
183
Pin Descriptions
DQS0–DQS7
CKE0, CKE1
CAS#,RAS#
DM0–DM7
CK0, CK0#
CK1, CK1#
SYMBOL
BA0, BA1
SA0–SA2
S0#, S1#
A0–A12
WE#,
SDA
SCL
Output
Output
Input/
Input/
TYPE
Input
Input
Input
Input
Input
Input
Input
Input
Input
Command Inputs: RAS#, CAS#, and WE# (along with S#) define
the command being entered.
Clock: CK, CK# are differential clock inputs. All address and
control input signals are sampled on the crossing of the
positive edge of CK, and negative edge of CK#. Output data
(DQs and DQS) is referenced to the crossings of CK and CK#.
Clock Enable: CKE HIGH activates and CKE LOW deactivates the
internal clock, input buffers and output drivers. Taking CKE
LOW provides PRECHARGE POWER-DOWN and SELF REFRESH
operations (all device banks idle), or ACTIVE POWER-DOWN
(row ACTIVE in any device bank). CKE is synchronous for
POWER-DOWN entry and exit, and for SELF REFRESH entry.
CKE is asynchronous for SELF REFRESH exit and for disabling
the outputs. CKE must be maintained HIGH throughout read
and write accesses. Input buffers (excluding CK, CK# and CKE)
are disabled during POWER-DOWN. Input buffers (excluding
CKE) are disabled during SELF REFRESH. CKE is an SSTL_2 input
but will detect an LVCMOS LOW level after VDD is applied and
until CKE is first brought HIGH. After CKE is brought HIGH, it
becomes an SSTL_2 input only.
Chip Selects: S# enables (registered LOW) and disables
(registered HIGH) the command decoder. All commands are
masked when S# is registered HIGH. S# is considered part of
the command code.
Bank Address: BA0 and BA1 define to which device bank an
ACTIVE, READ, WRITE, or PRECHARGE command is being
applied.
Address Inputs: Provide the row address for ACTIVE commands,
and the column address and auto precharge bit (A10) for
READ/WRITE commands, to select one location out of the
memory array in the respective device bank. A10 sampled
during a PRECHARGE command determines whether the
PRECHARGE applies to one device bank (A10 LOW, device bank
selected by BA0, BA1) or all device banks (A10 HIGH). The
address inputs also provide the op-code during a MODE
REGISTER SET command. BA0 and BA1 define which mode
register (mode register or extended mode register) is loaded
during the LOAD MODE REGISTER command.
Serial Clock for Presence-Detect: SCL is used to synchronize the
presence-detect data transfer to and from the module.
Presence-Detect Address Inputs: These pins are used to
configure the presence-detect device.
Serial Presence-Detect Data: SDA is a bidirectional pin used to
transfer addresses and data into and out of the presence-
detect portion of the module.
Data Write Mask. DM LOW allows WRITE operation. DM HIGH
blocks WRITE operation. DM lines do not affect READ
operation.
Data Strobe: Output with READ data, input with WRITE data.
DQS is edge-aligned with READ data, centered in WRITE data.
Used to capture data.
4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
200-PIN DDR SODIMM
512MB, 1GB (x64, DR)
DESCRIPTION
©2004 Micron Technology, Inc.