HFBR-57E0APZ Avago Technologies US Inc., HFBR-57E0APZ Datasheet - Page 6

• Manufacturer Part Number: HFBR-57E0APZ
• Description: TXRX MM SFP LC CONN BAIL DELATCH
• Manufacturer: Avago Technologies US Inc.
• Series: -r

Specifications of HFBR-57E0APZ

• Applications: Ethernet
• Mounting Type: SFP
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Wavelength: 1300nm
• Data Rate: 155MBd
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Table 2. Pin Description
Notes:
1.
2.
3.
4.
5.
6.
6
Pin
1
6
10
11
12
13
14
15
16
17
18
19
2
3
4
5
7
8
9
20
Pin 2 connected to internal ground.
Mod-Def 0, 1, 2. are the module definition pins. They should be pulled up with a 4.7 K - 10 KΩ resistor on the host board to a supply
less than V
Mod-Def 0 is grounded by the module to indicate that the module is present.
Mod-Def 1 is clock line of two wire serial interface for optional serial ID.
Mod-Def 2 is data line of two wire serial interface for optional serial ID.
LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 - 10 KΩ resistor on the host
board to a supply < V
sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to <0.8 V.
RD-/+: These are the differential receiver outputs. They are ac coupled 100 Ω differential lines which should be terminated with
100 Ω differential at the SERDES. The ac coupling is done inside the module and is thus not required on the host board. The voltage
swing on these lines will be between 400 and 2000 mV differential (200 - 1000 mV single ended) when properly terminated.
V
maximum supply current is 230 mA and the associated in-rush current will typically be no more than 30 mA above steady state after
500 nanoseconds.
TD-/+: These are the differential transmitter inputs. They are ac coupled differential lines with 100 Ω differential termination
inside the module. The ac coupling is done inside the module and is thus not required on the host board. The inputs will accept
differential swings of 400 - 2000 mV (200 - 1000 mV single ended), though it is recommended that values between 400 and 1200
mV differential (200 - 600 mV single ended) be used for best EMI performance. These levels are compatible with CML and LVPECL
voltage swings.
CC
R and V
Name
NC
MOD-DEF2
MOD-DEF1
MOD-DEF0
NC
LOS
RD-
RD+
V
Tx Disable
V
V
V
V
V
V
V
TD+
TD-
V
EE
EE
EE
EE
EE
CC
CC
EE
EE
T
R
R
R
R
T
T
R
T
CC
CC
T +0.3 V or V
T are the receiver and transmitter power supplies. They are defined as 2.97 - 3.63 V at the SFP connector pin. The
CC
T, R +0.3 V. When high, this output indicates the received optical power is below the worst case receiver
CC
Function/Description
Transmitter Ground
NC
Module Definition 2 - Two Wire Serial ID Interface
Module Definition 1 - Two Wire Serial ID Interface
Module Definition 0 - grounded in module
NC
Loss of Signal - high indicates loss of signal
Receiver Ground
Receiver Ground
Receiver Ground
Inverse Received Data Out
Received Data Out
Receiver Ground
Receiver Power -3.3 V ± 10%
Transmitter Power -3.3 V ± 10%
Transmitter Ground
Transmitter Data In
Inverse Transmitter Data In
Transmitter Ground
Transmitter Disable- Module disables on high or open
R +0.3 V.
MSA Notes
1
2
2
2
3
5
5
6
6
4
4