AFCT-5710PZ Avago Technologies US Inc., AFCT-5710PZ Datasheet - Page 6

• Manufacturer Part Number: AFCT-5710PZ
• Description: TXRX OPT SFF PLUGGABLE BAIL
• Manufacturer: Avago Technologies US Inc.
• Series: -r

Specifications of AFCT-5710PZ

• Data Rate: 1.25Gbd
• Wavelength: 1310nm
• Applications: Ethernet
• Voltage - Supply: 3.14 V ~ 3.47 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Function: SFP Optical Transceivers with Optional DMI for Gigabit Ethernet 1.25 GBd. Intended for premise, public and access networking applications.
• Product: Transceiver
• Maximum Rise Time: 0.26 ns/0.4 ns
• Maximum Fall Time: 0.26 ns/0.4 ns
• Pulse Width Distortion: 0.227 ns (Max)/0.267 ns (Max)
• Operating Supply Voltage: 3.14 V to 3.47 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 10 C
• Package / Case: SFP
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 1250MBd
• Optical Rise Time: 0.26/0.4ns
• Optical Fall Time: 0.26/0.4ns
• Jitter: 0.227/0.267ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 1355nm
• Package Type: SFP
• Operating Supply Voltage (min): 3.14V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.47V
• Operating Temp Range: -10C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Singlemode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Electrostatic Discharge (ESD)
There are two conditions in which immunity to ESD
damage is important:
The first condition is static discharge to the transceiver
during handling such as when the transceiver is inserted
into the transceiver port. To protect the transceiver,
it is important to use normal ESD handling precau-
tions including the use of grounded wrist straps, work
benches, and floor mats in ESD controlled areas. The ESD
sensitivity of the AFCT-571 Z is compatible with typical
industry production environments.
The second condition is static discharge to the exterior
of the host equipment chassis after installation. To the
extent that the duplex LC optical interface is exposed
to the outside of the host equipment chassis, it may be
subject to system-level ESD requirements. The ESD per-
formance of the AFCT-571 Z exceeds typical industry
standards. Table 1 documents ESD immunity to both of
these conditions.
Electromagnetic Interference (EMI)
Most equipment designs using the AFCT-571 Z SFPs
are subject to the requirements of the FCC in the
United States, CENELEC EN55022 (CISPR 22) in Europe
and VCCI in Japan. The metal housing and shielded
design of the transceiver minimize EMI and provide
excellent EMI performance.
EMI Immunity
The AFCT-571 Z transceivers have a shielded design
to provide excellent immunity to radio frequency
electromagnetic fields which may be present in some
operating environments.
6
Eye Safety
The AFCT-571 Z transceivers provide Class 1 eye
safety by design. Avago Technologies has tested the
transceiver design for regulatory compliance, under
normal operating conditions and under a single fault
condition. See Table 1.
Flammability
The AFCT-571 Z family of SFPs is compliant to UL
94V-0.
Customer Manufacturing Processes
This module is pluggable and is not designed for
aqueous wash, IR reflow, or wave soldering processes.
Caution
The AFCT-571 Z contains no user-serviceable parts.
Tampering with or modifying the performance of the
AFCT-571 Z will result in voided product warranty. It
may also result in improper operation of the transceiver
circuitry, and possible over-stress of the laser source.
Device degradation or product failure may result.
Connection of the AFCT-571 Z to a non-approved
optical source, operating above the recommended
absolute maximum conditions may be considered an
act of modifying or manufacturing a laser product. The
person(s) performing such an act is required by law to
re-certify and re-identify the laser product under the
provisions of U.S. 21 CF.