HFBR-1528Z Avago Technologies US Inc., HFBR-1528Z Datasheet - Page 9

• Manufacturer Part Number: HFBR-1528Z
• Description: XMITTER FIBER OPTIC 600NM 10MBD
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-1528Z

• Wavelength: 600nm
• Voltage - Forward (vf) Typ: 2.02V
• Current - Dc Forward (if): 1A
• Voltage - Dc Reverse (vr) (max): 5V
• Connector Type: Versatile Link
• Function: Ideal for solving problems with voltage isolation/insulation, EMI/RFI immunity or data security.
• Product: Transmitter
• Data Rate: 10 MBd
• Diode Capacitance: 60 pF
• Maximum Rise Time: 13 ns (Typ)
• Maximum Fall Time: 10 ns (Typ)
• Operating Supply Voltage: 4.75 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Data Rate Max: 10Mbps
• Forward Current If: 80mA
• Forward Voltage: 1.67V
• Reverse Voltage Vr: 5V
• Data Transmission Distance: 50ft
• Wavelength Typ: 660nm
• Msl: MSL 4 - 72 Hours
• Fiber Material: Plastic
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Capacitance: -
• Spectral Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With: Plastic Optical Fiber, Hard Clad Silica
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-2047

9
Receiver Electrical/Optical Characteristics
0 C to 70 C, 4.75 V V
Notes:
1. Optical flux, P (dBm) = 10 Log [P ( W)/1000 W].
2. Measured at the end of the fiber optic cable with large area detector.
3. R
4. Pulsed LED operation at I
HFBR-25X1Z Receiver
DO NOT CONNECT
DO NOT CONNECT
Absolute Maximum Ratings
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.01 F be connected from pin 2 to pin 3 of the receiver. Total lead length between both ends of the capacitor
Parameter
Input Optical Power
Level for Logic “0”
Input Optical Power
Level for Logic “1”
High Level Output Current
Low Level Output Current
High Level Supply
Current
Low Level Supply Current
Effective Diameter
Numerical Aperture
Internal Pull-up Resistor
Parameter
Storage Temperature
Operating Temperature
Lead Soldering Cycle
Supply Voltage
Output Collector Current
Output Collector Power Dissipation
Output Voltage
Pull-up Voltage
Fan Out (TTL)
width distortion of the receiver output signal.
and the pins should not exceed 20 mm.
L
is open.
5
8
CC
F
> 80 mA will cause increased link t
1000
5.25 V unless otherwise specified
Time
Temp.
4
3
2
1
Symbol
P
P
R
V
GROUND
V
I
I
NA
V
I
CCH
CCL
R
R(L)
R(H)
OH
D
CC
O
L
OL
L
–21.6
–21.6
Min.
680
PLH
Symbol
I
P
V
OAV
propagation delay time. This extended t
V
V
T
T
N
CC
OD
A
S
O
P
1000
Typ.
0.4
3.5
6.2
0.5
5
1
Min.
Max.
–0.5
–0.5
1700
–40
–40
–9.5
–8.7
–43
250
–5
0.5
6.3
10
Units
dBm
dBm
mm
mA
mA
V
A
Max.
+85
+85
260
V
10
25
40
18
7
5
CC
Note: Pins 5 and 8 are for mounting and
retaining purposes only. Do not electrically
connect these pins.
Pin #
1
2
3
4
5
8
PLH
V
I
V
I
V
I
V
I
P
V
P
V
P
OL
OL
OH
OL
OL
OL
OL
O
R
CC
R
CC
R
time contributes to increased pulse
= 0
= 18 V, P
= P
= -12.5 dBm
Conditions
= 8 mA
= 8 mA, 25 C
= 8 mA,
= 0.5 V
= 0.5 V
= 5.25 V
= 5.25 V,
= 5.25 V
250 A
Units
R(L)MIN
mW
sec
mA
V
V
V
C
C
C
R
= 0
Function
V
Ground
V
R
Do not connect
Do not connect
O
CC
L
Note 1
Note 2
Reference
Notes 1,
Note 1
Note 3
Note 3
Note 3
Note 3
Ref.
2, 4