FPSS1U TDK Corporation, FPSS1U Datasheet - Page 28

• Manufacturer Part Number: FPSS1U
• Description: RACK 3 SLOT FOR FPS1000
• Manufacturer: TDK Corporation
• Series: FPSr

Specifications of FPSS1U

• Accessory Type: Rack System
• No. Of Slots: 3
• Peak Reflow Compatible (260 C): No
• External Width: 19.00"
• Rack U Height: 1
• External Depth: 13.82"
• For Use With: 285-1239 - PWR SUP FNT END 48V 1008W 21A285-1238 - PWR SUP FNT END 32V 992W 31A285-1237 - PWR SUP FNT END 24V 960W 40A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: FPS1000 Series
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1240

CHAPTER 9
Notes:
*1: The Output of all the FPS1000 modules are connected in parallel in the rack.
*2: For input voltage lower than 100Vac, maximum output power derated by 10% of the power rating.
*3: For cases where conformance to to various safety standards (UL, EN etc.) is required, to be described
*4: Remote sensing can compensate up to 1V drop on each load wire.
*5: Not apllicable for units with I
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
1
2
3
4
5
6
7
8
9
as 100-240Vac (50/60Hz).
Number of power supply modules (*1)
Maximum output power
Input voltage / frequency range
Maximum input current (at 100/200Vac)
AC input connector
Output terminals
Remote sensing
Parallel operation
Series operation
Remote On/Off control
DC_OK signal
AC fail signal
Over Temperature alarm signal
Vout voltage trimming
Auxiliary power supply
Operating temperature
Storage temperature
Operating humidity
Storage humidity
Vibration
Shock
Applicable safety standards
Withstand voltage
Insulation resistance
Weight (Typ)
Size (W*H*D)
Warranty
FPS-S1U RACK SPECIFICATIONS
2
C bus option.
(*2)
(*3)
(*4)
(*5)
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Kg
---
Yr
W
A
V
Possible. Up to 3 racks with max 8 FPS 1000 units of the same voltage and current rating.
11.2~12.5VDC.Maximum output current:0.25A*Number of installed FPS1000 units.
Possible, via separate control for each FPS1000 unit .Refer to Instruction Manual.
Input-Output: 3000Vrms, 1min. Input-Ground: 2000Vrms, 1min. Output-Ground:
Separate control for each FPS 1000 unit , By electrical signal or dry contact
FPS-S1U :IEC inlet for each power supply module . FPS-S1U/P :None
More than 100Mohm at 25°C and 70% RH. Output-Ground: 500Vdc
Maximum 3 x FPS1000 modules of the same output voltage rating.
Possible. Up to 2 racks of the same voltage and current rating
Separate control for each FPS1000 unit, Open collector signal.
Separate control for each FPS1000 unit ,Open collector signal.
Separate control for each FPS1000 unit ,Open collector signal.
25
On when Vout >80% +/-5%. Max.sink current: 10mA
0~50°C: 100% load. Derate 2%/°C, 50°C to 60°C.
85~265Vac continuous, 47~63Hz, Single phase
440x44x351mm. Refer to Outline Drawing.
ON: 0~0.6V or short. OFF: 2~15V or open.
12.0/6.0 for each FPS1000 unit installed
Bus-bars.Refer to outline drawing.
10~90% RH, no condensation.
10~90% RH, no condensation.
Refer to Instruction Manual
Refer to Instruction Manual
Built to meet ETS 300 019
Built to meet ETS 300 019
UL60950-1, EN60950-1
500Vrms, 1min.
Two Years
Possible.
-30~85°C
3000
FPS-S1U Instruction Manual
3.7