P0033 Terasic Technologies Inc, P0033 Datasheet
P0033
Specifications of P0033
Related parts for P0033
P0033 Summary of contents
Page 1
THDB-HTG Terasic HSTC to GPIO Daughter Board User Manual Document Version 1.0 DEC. 23, 2008 by Terasic Terasic THDB-HTG ...
Page 2
INTRODUCTION ..........................................................................................................................................................1 1-1 F ................................................................................................................................................................................... 1 EATURES 1 ........................................................................................................................................................................... 1 ETTING ELP ARCHITECTURE .........................................................................................................................................................2 1 .......................................................................................................................................................... 2 AYOUT AND OMPONETS 1 ........................................................................................................................................................................ 4 LOCK IAGRAM BOARD COMPONENTS.............................................................................................................................................5 1-5 HSTC/HSMC E C XPANSION ONNECTOR 1-6 ...
Page 3
Introduction The THDB-HTG board is designed to convert a High-Speed Terasic connector (HSTC High-Speed Mezzanine connector (HSMC) I/Os to three 40-pin expansion prototype connectors, which are compatible with Altera DE2/DE1 expansion headers. Users can connect up to ...
Page 4
Architecture This chapter describes the architecture of the THDB-HTG board, including block diagram and components. Figure 2.1, Figure 2.2, and Figure 2.3 depict the layout of the board and indicate the locations of the connectors and key components. Expansion ...
Page 5
Architecture 180-pin Female HSTC Connector (J1) Figure 2.2 Back side of the TDRB-HTG board – HSTC version 180-pin Male HSMC Connector (J1) Figure 2.3 Back side of the TDRB-HTG board – HSMC version 3 ...
Page 6
The following components are provided on the THDB-HTG board : • HSTC/HSMC expansion connector (J1) • Expansion prototype connectors (J2,J3,J4) • I2C serial EEPROM (U1) Figure 2.4 shows the block diagram of the THDB-HTG board. To HSTC/HSMC Interface Host Board ...
Page 7
Board Components This section will describe the information of components, connector interfaces, and pin mappings on the THDB-HTG board in details. HSTC/HSMC Expansion Connector 1-5 This section describes the HSTC/HSMC connector on the THDB-HTG board There are two options ...
Page 8
J1 VCC33 HSTCA_CLKOUT_n0 HSTCA_CLKOUT_p0 HSTCA_TX_n0 HSTCA_TX_p0 HSTCA_TX_n1 HSTCA_TX_p1 HSTCA_TX_n2 21 ...
Page 9
Expansion Prototype Connectors 1-6 This section describes the expansion prototype connectors on the THDB-HTG board. The THDB-HTG board has three expansion prototype connectors (J2, J3, and J4) connected to the HSTC/HSMC connector directly. Each of the connectors has 36 prototyping ...
Page 10
J2 HSMC_CLKINn2 1 2 HSMC_RX_n16 HSMC_CLKINp2 3 4 HSMC_RX_p16 5 6 HSMC_RX_n15 HSMC_TX_n16 HSMC_RX_p15 HSMC_TX_p16 7 8 HSMC_RX_n14 HSMC_TX_n15 GND 5V HSMC_RX_p14 HSMC_TX_p15 13 14 HSMC_RX_n13 HSMC_TX_n14 HSMC_RX_p13 HSMC_TX_p14 19 20 HSMC_CLKOUTn2 ...
Page 11
Table 3.1 Pin mappings of the expansion prototype connector J2 Expansion Prototype Connector 1 – Pin J1 Pin J1 (HSTC Version) Signal Number Number ...
Page 12
Table 3.2 Pin mappings of the expansion prototype connector J3 Expansion Prototype Connector 1 – Pin J1 Pin J1 (HSTC Version) Signal Number Number ...
Page 13
Table 3.3 Pin mappings of the expansion prototype connector J4 Expansion Prototype Connector 1 – Pin J1 Pin J1 (HSTC Version) Signal Number Number 1 133 2 134 3 135 4 136 5 137 6 138 7 139 ...
Page 14
The THDB-HTG board provides users a prototyping area for signal measurement or debug. These prototyping points are connected to the HSTC/HSMC connector directly. Detailed I/O maps for HSTC and HSMC version are provided to help users locate the corresponding prototyping ...
Page 15
The THDB-HTG board provides a JTAG switch (SW1) to short the JTGA signal “HSTC_TDI” and “HSTC_TDO” together. When the THDB-HTG board is connected to a HSTC host board, this feature can bypass the JTAG signal from host board to form ...
Page 16
Table 3.4 The pin assignments of the I2C serial EEPROM EEPROM Pin Number U1-1 U1-2 U1-3 U1-4 U1-5 U1-6 U1-7 U1-8 This section describes the power supply on the THDB-HTG board. The power distribution on the THDB-HTG board is shown ...
Page 17
Demonstration This chapter illustrates how to use the THDB-HTG board to a HSTC/HSMC-interfaced host board. Connecting THDB-HTG Board to a Cyclone III Starter Board 1-12 This section describes how to use the THDB-HTG board with a Cyclone III Starter ...
Page 18
Connecting THDB-HTG Board to Altera DE3 Board 1-13 This section describes how to use the THDB-HTG board with Altera DE3 Board. Figure 4.2 illustrates how the THDB-HTG board is connected to the Altera DE3 board. Users need to pay extra ...
Page 19
Appendix Date DEC 23, 2009 Always Visit THDB-HTG Webpage for New Main board 1-16 We will be continuing providing interesting examples and labs on our THDB-HTG webpage. Please visit www.altera.com or HTG.terasic.com for more information. Appendix Mechanical 1-14 Revision ...
Page 20
... MH4 MH4 Copyright (c) 2008 by Terasic Technologies Inc. Taiwan. Copyright (c) 2008 by Terasic Technologies Inc. Taiwan. Copyright (c) 2008 by Terasic Technologies Inc. Taiwan. All rights reserved. All rights reserved. All rights reserved. No part of this schematic design may be reproduced, duplicated, or used without the prior written permission of Terasic. ...