XE8000EV104 Semtech, XE8000EV104 Datasheet - Page 67
XE8000EV104
Manufacturer Part Number
XE8000EV104
Description
EVAL BOARD FOR XE8805AMI028LF
Manufacturer
Semtech
Type
MCUr
Specifications of XE8000EV104
Contents
Fully Assembled Evaluation Board
For Use With/related Products
XE88LC05AMI028
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 67 of 156
- Download datasheet (2Mb)
Note: Depending on the status of the EnResPConf bit in RegSysCtrl, the reset conditions of the registers are
different. See the reset block documentation for more details on the resetpconf signal.
12.4 Port B capabilities
Table 12-7 shows the different usage that can be made of the port B with the order of priority. If a pair of pins is
selected to be analog, it overwrites the function and digital set-up. If the pin is not selected as analog, but a
function is enabled, it overwrites the digital set-up. If neither the analog nor function are selected for a pin, it is used
as an ordinary digital I/O. This is the default configuration at start-up.
12.5 Port B analog capability
12.5.1
Port B terminals can be attached to a 4 line analog bus by setting the PBAna[x] bits to 1 in the RegPBAna
register.
The other registers then define the connection of these 4 analog lines to the different pads of Port B. This can be
used to implement a simple LCD driver or A/D converter. Analog switching is available only when the circuit is
powered with sufficient voltage (see specification below). Below the specified supply voltage, only voltages that are
close to VSS or VBAT can be switched.
When PBAna[x] is set to 1, a pair of Port B terminals is switched from digital I/O mode to analog mode. The usage
of the registers RegPBPullup, RegPBOut and RegPBDir define the analog configuration (see Table 12-8).
When PBAna[x] = 1, then PBPullup[x] connects the pin to the analog bus. PBDir[x] and PBPOut[x] select which
of the 4 analog lines is used. For odd values of x, the selection bits are in the register RegPBOut (see Table 12-8).
For even values of x, the selection bits are in the register RegPBDir (see Table 12-9).
© Semtech 2006
Port B analog configuration
Table 12-8: Selection of the analog lines for PB[x] when x is odd and PBAna[x] = 1
Port B
name
PB[7]
PB[6]
PB[5]
PB[4]
PB[3]
PB[2]
PB[1]
PB[0]
if x is odd, PBOut[x, x-1]
analog
analog
analog
analog
analog
(high)
XX
00
01
10
11
Table 12-7: Different Port B functionality
PWM1 Counter C (C+D)
PWM0 Counter A (A+B)
clock CPU
functions
(medium)
uart Rx
usrt S1
usrt S0
32 kHz
uart Tx
usage (priority)
12-3
PBPullup[x]
1
1
1
1
0
PB[x] selection on
(low) (default)
High impedance
analog line 0
analog line 1
analog line 2
analog line 3
digital
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
XE8805/05A
www.semtech.com
Related parts for XE8000EV104
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: