DEMO9S08EL32 Freescale Semiconductor, DEMO9S08EL32 Datasheet

DEMO9S08EL32

Manufacturer Part Number

DEMO9S08EL32

Description

BOARD DEMO FOR 9S08 EL MCU

Manufacturer

Freescale Semiconductor

Type

MCUr

Datasheets

1.DEMO9S08EL32.pdf (356 pages)

2.DEMO9S08EL32.pdf (14 pages)

3.DEMO9S08EL32.pdf (2 pages)

Specifications of DEMO9S08EL32

Contents

Evaluation Board

Processor To Be Evaluated

MC9S08EL32

Data Bus Width

8 bit

Interface Type

RS-232, USB

Operating Supply Voltage

12 V

Silicon Manufacturer

Freescale

Core Architecture

HCS08

Core Sub-architecture

HCS08

Silicon Core Number

MC9S08

Silicon Family Name

S08EL

Rohs Compliant

Yes

For Use With/related Products

MC9S08EL32

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (38Kb)

D E M O 9 S 0 8 E L 3 2

Q U I C K

DEMO9S08EL32 QUICK START GUIDE

Introduction and Default Settings

This quick start guide will show how to connect the target board to a PC, install the correct version of CodeWarrior

Development Studio, and execute a simple demonstration program loaded in FLASH memory. The default

jumper settings for the DEMO9S08EL32 are shown below

Install CodeWarrior Development Studio for HC(S)08 Special Edition

The DEMO9S08EL32 board ships with CodeWarrior Development Studio for Microcontrollers, a complete Inte-

grated Development Environment (IDE) that provides a highly visual and automated framework to accelerate the

development of the most complex embedded applications. To install the IDE, refer to the “CodeWarrior Devel-

opment Studio” DVD case and follow the steps in the included Quick Start Guide.

CodeWarrior Development Studio must be properly installed before attempting to connect the target board to the

host PC. Otherwise, the necessary USB drivers will not be available and the host PC will not recognize the target

board when connected.

Run the LED_DEMO Program

The DEMO9S08EL32 ships with a simple demonstration program loaded into on-chip FLASH memory. This

demonstration program executes when power is applied or when the RESET button is pressed. The source code

for this demo program can be found in the LED_DEMO.zip file on the Axiom Support CD in the /Examples folder.

Follow the steps below to run the LED_DEMO program.

1. Verify the configuration jumpers are set to the default position. Refer to Figure 1 above.

2. Connect the included USB cable between an open USB port on the host PC and the USB connector on the

3. Follow the on-screen instructions to install the necessary USB drivers.

4. After the USB drivers are properly installed, the USB, POWER OUT, and +5V LED’s will be ON.

5. The LED_DEMO program will execute - LED1 toggles at approximately 4Hz. LED2 toggles each time SW2 is

target board.

pressed.

S T A R T

G U I D E

Figure 1: DEMO9S08EL32 Default Settings

R E V

D O C - 0 4 1 0 - 0 2 0

1 . 1 ,

Spencer Ruggles

0 5 / 2 0 0 7

Related parts for DEMO9S08EL32

DEMO9S08EL32 Summary of contents

Page 1

... Run the LED_DEMO Program The DEMO9S08EL32 ships with a simple demonstration program loaded into on-chip FLASH memory. This demonstration program executes when power is applied or when the RESET button is pressed. The source code for this demo program can be found in the LED_DEMO.zip file on the Axiom Support CD in the /Examples folder. ...

Page 2

... Ensure serial cable is securely attached to host PC and target board If the above Troubleshooting Tips fail to correct the problem, please contact Freescale Semiconductors for further assistance. Please refer to the Technical Information Card (TIC) included in the kit. Assistance may also be found by contacting Axiom Manufacturing at support@axman.com. ...

Related keywords

demo9s08sg32
demo9s08el32
demo9s12xsfame
demo9s12xep100
demo9s12xdt512
demo9s12ne64
demo9s08ll16
demo9s08el32auto
DEMO9S08EL32 datasheet
DEMO9S08EL32 data sheet
DEMO9S08EL32 pdf datasheet
DEMO9S08EL32 component
DEMO9S08EL32 part
DEMO9S08EL32 distributor
DEMO9S08EL32 RoHS
DEMO9S08EL32 datasheet download