KIT908E624DWBEVB Freescale Semiconductor, KIT908E624DWBEVB Datasheet - Page 29

• Manufacturer Part Number: KIT908E624DWBEVB
• Description: KIT EVAL 908E624 TRPL W/MCU/LIN
• Manufacturer: Freescale Semiconductor
• Type: MCUr

Specifications of KIT908E624DWBEVB

• Contents: *
• Silicon Manufacturer: Freescale
• Core Architecture: HC08
• Core Sub-architecture: HC08
• Silicon Core Number: MC68HC908
• Silicon Family Name: HC08E
• For Use With/related Products: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SPI REGISTER OVERVIEW
.
Table 7. SPI Register Overview
SPI Control Register (Write)
Table 8. Control Bits Function (Write Operation)
LINSL2 : 1 — LIN Baud Rate and Low-Power Mode
Selection Bits
power mode in accordance with
LINSL2 : 1 bits.
Table 9. LIN Baud Rate and Low-Power Mode Selection
LIN-PU — LIN Pullup Enable Bit
Stop modes.
is used to pull the LIN terminal in recessive state. In case of
Analog Integrated Circuit Device Data
Freescale Semiconductor
Notes
LINSL2 LINSL1 LIN-PU HS3ON HS2ON HS1ON MODE2 MODE1
LINSL2
28.
29.
Write Reset Condition
D7
Table 7
Table 8
These bits select the LIN slew rate and requested low-
This bit controls the LIN pullup resistor during Sleep and
• 1 = Pullup disconnected in Sleep and Stop modes.
• 0 = Pullup connected in Sleep and Stop modes.
In case the Pullup is disconnected a small current source
Write Reset Value
0
0
1
1
Information
Read / Write
D7 signals interrupts and wake-up interrupts, D6:D0 indicated the source.
The first SPI read after reset returns the BATFAIL flag state on bit D4.
Read
Write
D6
summarizes the SPI Register bit meaning, reset value, and bit reset condition.
shows the SPI Control register bits by name.
Bits
LINSL1
0
1
0
1
D5
Low-Power Mode (Sleep or Stop) Request
D4
INTSRC
Baud Rate up to 20 kbps (normal)
Baud Rate up to 10 kbps (slow)
LINSL2
RESET
POR,
Baud Rate up to 100 kbps
D7
Fast Program Download
0
D3
Table
(28)
Description
9. Reset clears the
LINFAIL
LINSL1
RESET
D2
LINWU
POR,
D6
or
0
D1
LIN-PU
POR
HVF
D5
D0
0
POR, RESET
BATFAIL
HS3ON
an erroneous short of the LIN bus to ground this will
significantly reduce the power consumption, e.g. in
combination with STOP/SLEEP mode.
HS3ON : HS1ON — High Side H3 : HS1 Enable Bits
terminal must be connected to the VDD terminal.
MODE2 : 1 — Mode Section Bits
watchdog in accordance with
Table 10. Mode Selection Bits
these modes are not affected by noise issue during SPI
transmission, the Sleep / Stop commands require two SPI
transmissions.
Notes
LVF
D4
30.
31.
MODE2
or
0
These bits enable the HSx. Reset clears the HSxON bit.
• 1 = HSx switched on (refer to Note below).
• 0 = HSx switched off.
Note If no PWM on HS1 and HS2 is required, the PWMIN
The MODE2 : 1 bits control the operating modes and the
To safely enter Sleep or Stop mode and to ensure that
0
0
1
1
(29)
To enter Sleep and Stop mode, a special sequence of SPI
commands is implemented.
The device stays in Run (Normal) mode.
Bit
MODE1
HS2ON
RESET
VDDT
POR,
D3
0
0
1
0
1
LOGIC COMMANDS AND REGISTERS
HS1ON
RESET
HSST
POR,
FUNCTIONAL DEVICE OPERATION
D2
0
Table
Watchdog Clear
Run (Normal) Mode
Sleep Mode
Stop Mode
10.
Description
MODE2
D1
L2
—
—
(30)
(30)
(31)
MODE1
D0
L1
—
—
908E624
29