R0E0200F1EMU00 Renesas Electronics America, R0E0200F1EMU00 Datasheet - Page 29
R0E0200F1EMU00
Manufacturer Part Number
R0E0200F1EMU00
Description
DEV EMULATOR E200 MAIN BODY
Manufacturer
Renesas Electronics America
Series
SuperH®r
Type
In-Circuit Emulatorr
Datasheet
1.R0E0200F0ACC00.pdf
(76 pages)
Specifications of R0E0200F1EMU00
Contents
Emulator Board, Cables, Software and Documentation
For Use With/related Products
SH7080
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 29 of 76
- Download datasheet (2Mb)
2.6
Figures 2.12 and 2.13 show recommended circuits for connection between the H-UDI and AUD
port connectors (36 pins) and the MCU when the emulator is in use.
Notes: 1. Do not connect anything to the N.C. pins of the H-UDI port connector.
2.6.1
2. The ASEMD0# pin must be 0 when the emulator is connected and 1 when the emulator
3. When a network resistance is used for pull-up, it may be affected by a noise. Separate
4. The pattern between the H-UDI port connector and the MCU must be as short as
5. The AUD signals (AUDCK, AUDATA3 to AUDATA0, and _AUDSYNC) operate in
6. Supply the operating voltages of the H-UDI and AUD of the MCU to the UVCC pin.
7. The resistance values shown in figures 2.12 and 2.13 are for reference.
8. For the AUDCK pin, guard the pattern between the H-UDI port connector and the
9. For the pin processing in cases where the emulator is not used, refer to the hardware
Recommended Circuit (36-Pin Type)
Recommended Circuit between the H-UDI Port Connector and the
MCU
is not connected, respectively.
(1) When the emulator is used: ASEMD0# = 0
(2) When the emulator is not used: ASEMD0# = 1
Figures 2.12 and 2.13 show examples of circuits that allow the ASEMD0# pin to be
GND (0) whenever the emulator is connected by using the H-UDI/AUD probe. When
the ASEMD0# pin is changed by switches, etc., ground pin 22. Do not connect this pin
to the ASEMD0# pin.
TCK from other resistances.
possible. Do not connect the signal lines to other components on the board.
high speed. Isometric connection is needed if possible. Do not separate connection nor
connect other signal lines adjacently.
MCU at GND level.
manual of the related MCU.
Rev. 4.00 Feb. 18, 2009 Page 21 of 64
REJ10J1662-0400
Related parts for R0E0200F1EMU00
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: