COP8SA-DM National Semiconductor, COP8SA-DM Datasheet - Page 212
COP8SA-DM
Manufacturer Part Number
COP8SA-DM
Description
MODULE DEBUGGING FOR COP8SA
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of COP8SA-DM
Module/board Type
Debugger Module
For Use With/related Products
Cop 8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*COP8SA-DM
- Current page: 212 of 254
- Download datasheet (2Mb)
Power-on wakeup is a technique used in battery powered applications such as electronic
keys or digital scales to save battery power. Instead of using the HALT mode when the
application is not in use, the microcontroller device is powered off. If there is only one
input switch in the application, the implementation is simple. This switch is put in series
with the battery, providing power to the circuit when the switch is closed.
If there is more than one switch, power-on wakeup can be achieved by using an NPN
transistor and one resistor per switch as shown in Figure 4-8. Here, the circuit ground is
connected to the battery negative terminal via the NPN transistor. If the base is floating,
it will not conduct. If the base is pulled to V
conduct, powering up the circuit.
An alternative technique is shown in Figure 4-9. Here the positive terminal of the
battery is connected to the V
switch is pressed, power is applied to the V
connected to open switches to ground. If the switch is closed, the voltage on the switch
will be V
L pin, the COP device would be driven outside the operating specification. Therefore,
series protection resistors are used on all Port L pins connected to the switches.
4-20
COP8SAx7 APPLICATION IDEAS
CC
plus the diode voltage drop. If this potential were directly applied to the Port
Figure 4-8 Power Wakeup Using An NPN Transistor
CC
Vcc
line via a switch, a diode and two resistors per line. If a
L0
L1
L2
L3
COP8SAx7
CC
GND
Vcc
line. The pull-down resistors pull any ports
CC
via a current-limiting resistor, it will
+
+
Vcc
Related parts for COP8SA-DM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PROGRAMING UNIT FOR COP8SA PARTS
Manufacturer:
National Semiconductor
Part Number:
Description:
ADAPTER SOIC 16,20,28,44 PLCC
Manufacturer:
National Semiconductor
Part Number:
Description:
8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory/ Power On Reset/ and Very Small Packaging
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet: