SI3210DCQ1-EVB Silicon Laboratories Inc, SI3210DCQ1-EVB Datasheet - Page 30

• Manufacturer Part Number: SI3210DCQ1-EVB
• Description: DAUGHTERCARD W/SI3201 INTERFACE
• Manufacturer: Silicon Laboratories Inc
• Series: ProSLIC®r
• Type: SLIC/CODECr

Specifications of SI3210DCQ1-EVB

• Contents: Evaluation Board and CD-ROM
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With/related Products: Si3210
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Si3210/Si3211
2.1.9. Linefeed Calibration
An internal calibration algorithm corrects for internal and
external component errors. The calibration is initiated by
setting the CAL bit in direct Register 96. Upon
completion of the calibration cycle, this bit is
automatically reset.
It is recommended that a calibration be executed
following system power-up. Upon release of the chip
reset, the Si3210 will be in the open state. After
powering up the dc-dc converter and allowing it to settle
for time (t
Additional calibrations may be performed, but only one
calibration should be necessary as long as the system
remains powered up.
During calibration, V
controlled by the calibration engine to provide the
correct external voltage conditions for the algorithm.
Calibration should be performed in the on-hook state.
RING or TIP must not be connected to ground during
the calibration.
When using the Si3201, automatic calibration routines
for RING gain mismatch and TIP gain mismatch should
not be performed. Instead of running these two
calibrations automatically, consult “AN35: Si321x User’s
Quick Reference Guide” and follow the instructions for
manual calibration.
2.2. Battery Voltage Generation and
The ProSLIC supports two modes of battery supply
operation. First, the Si3210 integrates a dc-dc converter
controller that dynamically regulates a single output
voltage. This mode eliminates the need to supply large
external battery voltages. Instead, it converts a single
positive input voltage into the real-time battery voltage
needed for any given state according to programmed
linefeed parameters. Second, the Si3211 supports
switching between high and low battery voltage
supplies, as would a traditional monolithic SLIC.
For single to low channel count applications, the Si3210
proves to be an economical choice, as the dc-dc
converter eliminates the need to design and build high-
voltage power supplies. For higher channel count
applications where centralized battery voltage supply is
economical, or for modular legacy systems where
battery voltage is already available, the Si3211 is
recommended.
2.2.1. DC-DC Converter General Description
The dc-dc converter dynamically generates the large
negative voltages required to operate the linefeed
interface. The Si3210 acts as the controller for a buck-
30
Switching
(Si3210/Si3210M Only)
settle
) the calibration can be initiated.
BAT
, V
TIP
, and V
RING
voltages are
Rev. 1.42
boost dc-dc converter that converts a positive dc
voltage into the desired negative battery voltage. In
addition to eliminating external power supplies, this
allows the Si3210 to dynamically control the battery
voltage to the minimum required for any given mode of
operation.
Two different dc-dc circuit options are offered: a BJT/
inductor version and a MOSFET/transformer version.
Due to the differences on the driving circuits, there are
two different versions of the Si3210. The Si3210
supports the BJT/inductor circuit option, and the
Si3210M version supports the MOSFET solution. The
only difference between the two versions is the polarity
of the DCFF pin with respect to the DCDRV pin. For the
Si3210, DCDRV and DCFF are opposite polarity. For
the Si3210M, DCDRV and DCFF are the same polarity.
Table 27 summarizes these differences.
Extensive design guidance on each of these circuits can
be obtained from Application Note 45 (AN45) and from
an interactive dc-dc converter design spreadsheet. Both
of these documents are available on the Silicon
Laboratories website (www.silabs.com).
2.2.2. BJT/Inductor Circuit Option Using Si3210
The BJT/Inductor circuit option, as defined in Figure 10
on page 18, offers a flexible, low-cost solution.
Depending on selected L1 inductance value and the
switching frequency, the input voltage (V
from 5 V to 30 V. By nature of a dc-dc converter’s
operation, peak and average input currents can become
large with small input voltages. Consider this when
selecting the appropriate input voltage and power rating
for the V
For this solution, a PNP power BJT (Q7) switches the
current flow through low ESR inductor L1. The Si3210
uses the DCDRV and DCFF pins to switch Q7 on and
off. DCDRV controls Q7 through NPN BJT Q8. DCFF is
ac coupled to Q7 through capacitor C10 to assist R16 in
turning off Q7. Therefore, DCFF must have opposite
polarity to DCDRV, and the Si3210 (not Si3210M) must
be used.
Notes:
Table 27. Si3210 and Si3210M Differences
1. DCFF signal polarity with respect to DCDRV signal.
2. Direct Register 93, bit 5; This is a read-only bit.
Si3210M
Device
Si3210
DC
power supply.
DCFF Signal
= DCDRV
= DCDRV
Polarity
DC
DCPOL
) can range
0
1