1213860-1 Tyco Electronics, 1213860-1 Datasheet

CERTI-CRIMP II ADAPT-SDE BENCH

1213860-1

Manufacturer Part Number
1213860-1
Description
CERTI-CRIMP II ADAPT-SDE BENCH
Manufacturer
Tyco Electronics
Series
Certi-Crimp™r
Datasheet
1.1213860-1.pdf (5 pages)

Specifications of 1213860-1

Accessory Type
Handle
Tool Type
Tool Holder Assembly
For Use With/related Products
SDE Electric Bench Terminator
Lead Free Status / RoHS Status
Not applicable / Not applicable
Features
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
1. INTRODUCTION
The CERTI–CRIMP II Tool Holder Assembly
1213860–1 is used to adapt the crimping head from a
CERTI–CRIMP II Hand Tool to an SDE Electric
Bench Terminator. Figure 1 shows a typical crimping
head, mounted to CERTI–CRIMP II Tool Holder
Assembly 1213860–1, installed onto an SDE Electric
Bench Terminator.
This instruction sheet provides:
E
NOTE
S
S
S
S
Instructions for installing and removing the tool
holder assembly to the Electric Bench Machine
Instructions for installing the crimping head
onto the tool holder assembly
Instructions for adjusting the crimp height
Maintenance, inspection, and repair
instructions for the tool holder assembly
Figures and illustrations are for reference only,
and are not to scale.
CERTI-CRIMP* II Tool Holder Assembly
1213860-1 (for Use with the SDE Electric
Bench Terminator)
Figure 1
For information concerning the setup and operation of
the SDE Electric Bench Terminator, refer to Customer
Manual 409–10052.
Read this instruction sheet, and the related customer
manual, thoroughly before using the tool holder
assembly.
2. DESCRIPTION
The tool holder assembly facilitates the connection of
the crimping head to the SDE Electric Bench Machine
and provides the necessary straight line motion of the
movable die when the SDE Electric Bench Machine is
actuated.
The tool holder assembly features a switch (handle)
and three quick pins. See Figure 2. The switch
(handle) can be used to manually open and close the
dies of the crimping head for insertion and removal of
the product.
www.tycoelectronics.com
408-10021
1

1213860-1 Summary of contents

Page 1

... S Maintenance, inspection, and repair instructions for the tool holder assembly E CERTI-CRIMP* II Tool Holder Assembly 1213860-1 (for Use with the SDE Electric Bench Terminator) Figure 1 For information concerning the setup and operation of the SDE Electric Bench Terminator, refer to Customer Manual 409–10052. ...

Page 2

... Refer to Figure 3 and Figure 4. 4. Refer to Paragraph 3.2, to remove and install the crimping dies CERTI-CRIMP II Tool Holder Assembly 1213860-1 Figure 2 B. Removal DANGER To avoid personal injury, be sure the SDE Electric Bench Terminator is disconnected from the power source prior to the installation or removal of the tool holder assembly ...

Page 3

... The center pin will be used to secure the movable die of the crimp head to the ram of the tool holder assembly. A Rev CERTI-CRIMP II Tool Holder Assembly 1213860-1 A. Installation These pins must be removed prior to installing the crimping head. 1. Remove the quick–release pins shown in Figure 4. ...

Page 4

... Make certain all surfaces are protected with a thin coat of any good SAE 20 motor oil. DO NOT oil excessively CERTI-CRIMP II Tool Holder Assembly 1213860-1 4. When the tool holder assembly is not in use, store clean, dry area. 6.2. Lubrication Lubricate all pins, pivot points, and bearing surfaces with a high quality grease ...

Page 5

... CERTI-CRIMP II Tool Holder Assembly 1213860-1 CUSTOMER-REPLACEABLE PARTS ITEM PART NUMBER A DESCRIPTION Figure 7 408-10021 QTY PER ADAPTER 5 ...