679301-1 Tyco Electronics, 679301-1 Datasheet

no-image

679301-1

Manufacturer Part Number
679301-1
Description
TOOL 22-10AWG SOLIS CRIMP HEAD
Manufacturer
Tyco Electronics
Datasheets
1.189721-1.pdf (5 pages)
2.679301-1.pdf (7 pages)

Specifications of 679301-1

Lead Free Status / RoHS Status
Not applicable / Not applicable
Pneumatic Crimping Heads 679301–1, 1338757–1,
and 1338758–1 are designed to crimp SOLISTRAND
terminals and splices on solid or stranded copper
wire. See Figure 2. The crimping head is used with
626 Pneumatic Tooling Assemblies. Figure 1 shows
the tool holder assembly, and list the power units for
the crimping heads.
This instruction sheet provides recommended
procedures for wire preparation, crimp head
installation, crimping, and maintenance and
inspection. For information concerning tool setup and
operation, refer to the customer manual packaged
with the appropriate tool. Product specifications and
part numbers are available in Tyco Electronic
Catalogs. See Figure 1.
Read these instructions thoroughly before
proceeding.
Reasons for reissue are provided in Section 8,
REVISION SUMMARY.
E
i
All dimensions in this document are in millimeters
[with inches in brackets]. Figures and Illustrations
are for reference only and are not drawn to scale.
Figure 1
The pneumatic crimping heads consist of integral
jaws which close in an arc–like motion. After an
operator locates the terminal or splice between the
crimping jaws and inserts the stripped wire, the tool is
activated to crimp the terminal or splice to the wire.
i
Crimping heads are coated with a preservative to
prevent rust and corrosion. Wipe any excess
preservative from the head, particularly from
crimping surfaces.
To avoid personal injury, ALWAYS disconnect tool
from air supply before installing crimping head.
Do NOT operate pneumatic tool without proper
crimping head installed; make sure that the
quick-pins are FULLY tightened to avoid personal
injury and damage to the tool.

679301-1 Summary of contents

Page 1

... Pneumatic Crimping Heads 679301–1, 1338757–1, and 1338758–1 are designed to crimp SOLISTRAND terminals and splices on solid or stranded copper wire. See Figure 2. The crimping head is used with 626 Pneumatic Tooling Assemblies. Figure 1 shows the tool holder assembly, and list the power units for the crimping heads ...

Page 2

Pneumatic Crimping Heads WIRE WIRE CRIMPING TERMINAL RANGE HEAD STANDARD (AWG) (AWG) MIN 1. Remove quick pins from tool holder. 2. Insert crimping head into tool holder as shown in Figure 1. 3. After crimping head is properly aligned, ...

Page 3

... Remove dust, moisture, and other contaminants with a clean, soft brush lint–free cloth. Do NOT use objects that could damage the heads. 2. Make sure pins, rings, and other components are in place and secure. Tyco Electronics Corporation 408-4072 Center Splice in Dies Do Not Allow Wire ...

Page 4

Pneumatic Crimping Heads DANGER Make sure quick pins, are in place and FULLY tightened to avoid personal injury and damage to the tool. 3. Make certain all surfaces are protected with a Accept 4 thin coat of any good ...

Page 5

... Inspect the crimp area for flattened, chipped, or broken areas. Although the crimping chambers may gage within permissible limits, worn or damaged die closure surfaces are objectionable and will affect the quality of the crimp. GO Dimension 679301-1 22-16 679301-1 16-14 16-14HD / 12-10 1338757-1 8 1338758 ...

Page 6

... Align the GO element with the crimping chamber. Push the GO element straight into the crimping chamber without using force. The GO element must pass completely through the crimping chamber. See Figure 8. 4. Align the NO–GO element with the crimping chamber, and try to insert it straight into the 18 679301 crimping chamber. The NO– ...

Page 7

... Pneumatic Crimping Heads 1338757-1 ITEM DESCRIPTION DESCRIPTION NO Recommended Spares D 1338758-1 TOOLING PART NUMBER 679301-1 1338757-1 1338758-1 Figure 9 (end) 408-4072 QTY PER ASSY 7 ...