PIC18F25J11-I/ML Microchip Technology, PIC18F25J11-I/ML Datasheet - Page 55

• Manufacturer Part Number: PIC18F25J11-I/ML
• Description: IC PIC MCU FLASH 32K 2V 28-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F25J11-I/ML

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Interface: EUSART, I2C, SPI
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183022, DM183032, DV164136, MA180023
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

3.7
The Ultra Low-Power Wake-up (ULPWU) on RA0 allows
a slow falling voltage to generate an interrupt without
excess current consumption.
Follow these steps to use this feature:
1.
2.
3.
4.
5.
6.
7.
8.
When the voltage on RA0 drops below V
will be generated, which will cause the device to
wake-up and execute the next instruction.
This feature provides a low-power technique for
periodically waking up the device from Sleep mode.
The time-out is dependent on the discharge time of the
RC circuit on RA0.
When the ULPWU module causes the device to
wake-up from Sleep mode, the WDTCON<ULPLVL>
bit is set. When the ULPWU module causes the device
to
(DSWAKEL<5>) bit is set. Software can check these
bits upon wake-up to determine the wake-up source.
Also in Sleep mode, only the remappable output func-
tion, ULPWU, will output this bit value to an RPn pin for
externally detecting wake-up events.
© 2009 Microchip Technology Inc.
Configure a remappable output pin to output the
ULPOUT signal.
Map an INTx interrupt-on-change input function
to the same pin as used for the ULPOUT output
function. Alternatively, in step 1, configure
ULPOUT
interrupt-on-change pin.
Charge the capacitor on RA0 by configuring the
RA0 pin to an output and setting it to ‘1’.
Enable interrupt for the corresponding pin
selected in step 2.
Stop charging the capacitor by configuring RA0
as an input.
Discharge the capacitor by setting the ULPEN
and ULPSINK bits in the WDTCON register.
Configure Sleep mode.
Enter Sleep mode.
wake-up
Ultra Low-Power Wake-up
from
to
output
Deep
Sleep,
onto
a
IL
the
, an interrupt
PORTB
DSULP
PIC18F46J11 FAMILY
See Example 3-1 for initializing the ULPWU module.
A series resistor between RA0 and the external
capacitor provides overcurrent protection for the
RA0/AN0/C1INA/ULPWU/RP0 pin and can allow for
software calibration of the time-out (see Figure 3-9).
FIGURE 3-9:
A timer can be used to measure the charge time and
discharge time of the capacitor. The charge time can
then be adjusted to provide the desired interrupt delay.
This technique will compensate for the affects of
temperature, voltage and component accuracy. The
peripheral can also be configured as a simple Program-
mable Low-Voltage Detect (LVD) or temperature
sensor.
Note:
Note:
For module-related bit definitions, see the
WDTCON
“Watchdog Timer (WDT)” and the
DSWAKEL register (Register 3-6).
RA0
For more information, refer to AN879,
“Using the Microchip Ultra Low-Power
Wake-up
(DS00879).
SERIAL RESISTOR
Module”
register
R
1
application
in
DS39932C-page 55
C
1
Section 25.2
note