AT90PWM3-16SQ Atmel, AT90PWM3-16SQ Datasheet - Page 168

• Manufacturer Part Number: AT90PWM3-16SQ
• Description: IC AVR MCU FLASH 8K 32SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM3-16SQ

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-SOIC (7.5mm Width)
• Processor Series: AT90PWMx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 27
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRFBKIT, ATAVRISP2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• On-chip Dac: 10 bit, 1 Channel
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOICATAVRMC200 - KIT EVAL FOR AT90PWM3 ASYNCATAVRFBKIT - KIT DEMO BALLAST FOR AT90PWM2ATSTK520 - ADAPTER KIT FOR 90PWM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16.25.15 PSC n Input B Control Register – PFRCnB
168
AT90PWM2/3/2B/3B
The Input Control Registers are used to configure the 2 PSC’s Retrigger/Fault block A & B. The
2 blocks are identical, so they are configured on the same way.
• Bit 7 – PCAEnx : PSC n Capture Enable Input Part x
Writing this bit to one enables the capture function when external event occurs on input selected
as input for Part x (see PISELnx bit in the same register).
• Bit 6 – PISELnx : PSC n Input Select for Part x
Clear this bit to select PSCINn as input of Fault/Retrigger block x.
Set this bit to select Comparator n Output as input of Fault/Retrigger block x.
• Bit 5 –PELEVnx : PSC n Edge Level Selector of Input Part x
When this bit is clear, the falling edge or low level of selected input generates the significative
event for retrigger or fault function .
When this bit is set, the rising edge or high level of selected input generates the significative
event for retrigger or fault function.
• Bit 4 – PFLTEnx : PSC n Filter Enable on Input Part x
Setting this bit (to one) activates the Input Capture Noise Canceler. When the noise canceler is
activated, the input from the retrigger pin is filtered. The filter function requires four successive
equal valued samples of the retrigger pin for changing its output. The Input Capture is therefore
delayed by four oscillator cycles when the noise canceler is enabled.
• Bit 3:0 – PRFMnx3:0: PSC n Fault Mode
These four bits define the mode of operation of the Fault or Retrigger functions.
(see PSC Functional Specification for more explanations)
Table 16-17. Level Sensitivity and Fault Mode Operation
Bit
Read/Write
Initial Value
PRFMnx3:0
0000b
0001b
0010b
0011b
0100b
0101b
0110b
0111b
1000b
PCAEnB
R/W
7
0
Description
No action, PSC Input is ignored
PSC Input Mode 1: Stop signal, Jump to Opposite Dead-Time and Wait
PSC Input Mode 2: Stop signal, Execute Opposite Dead-Time and Wait
PSC Input Mode 3: Stop signal, Execute Opposite while Fault active
PSC Input Mode 4: Deactivate outputs without changing timing.
PSC Input Mode 5: Stop signal and Insert Dead-Time
PSC Input Mode 6: Stop signal, Jump to Opposite Dead-Time and Wait.
PSC Input Mode 7: Halt PSC and Wait for Software Action
PSC Input Mode 8: Edge Retrigger PSC
PISELnB
R/W
6
0
PELEVnB
R/W
5
0
PFLTEnB
R/W
4
0
PRFMnB3 PRFMnB2 PRFMnB1 PRFMnB0
R/W
3
0
R/W
2
0
R/W
1
0
R/W
0
0
4317J–AVR–08/10
PFRCnB