PIC18LF4420-I/PT Microchip Technology, PIC18LF4420-I/PT Datasheet - Page 144

• Manufacturer Part Number: PIC18LF4420-I/PT
• Description: IC MCU FLASH 8KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF4420-I/PT

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 36
• Interface Type: I2C/SPI/USART
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F2420/2520/4420/4520
15.3
In Compare mode, the 16-bit CCPRx register value is
constantly compared against either the TMR1 or TMR3
register pair value. When a match occurs, the CCPx pin
can be:
• driven high
• driven low
• toggled (high-to-low or low-to-high)
• remain unchanged (that is, reflects the state of the
The action on the pin is based on the value of the mode
select bits (CCPxM<3:0>). At the same time, the
interrupt flag bit, CCPxIF, is set.
15.3.1
The user must configure the CCPx pin as an output by
clearing the appropriate TRIS bit.
FIGURE 15-2:
DS39631E-page 142
I/O latch)
Note:
Compare Mode
CCP PIN CONFIGURATION
Clearing the CCP2CON register will force
the RB3 or RC1 compare output latch
(depending on device configuration) to the
default low level. This is not the PORTB or
PORTC I/O data latch.
0
1
COMPARE MODE OPERATION BLOCK DIAGRAM
CCPR2H
CCPR1H
TMR1H
TMR3H
T3CCP1
Comparator
Comparator
CCPR2L
CCPR1L
TMR1L
TMR3L
Compare
Compare
Match
Match
0
1
Set CCP1IF
T3CCP2
Set CCP2IF
(Timer1/Timer3 Reset, A/D Trigger)
15.3.2
Timer1 and/or Timer3 must be running in Timer mode
or Synchronized Counter mode if the CCP module is
using the compare feature. In Asynchronous Counter
mode, the compare operation may not work.
15.3.3
When the Generate Software Interrupt mode is chosen
(CCPxM<3:0> = 1010), the corresponding CCPx pin is
not affected. A CCP interrupt is generated when the
CCPxIF interrupt flag is set while the CCPxIE bit is set.
15.3.4
Both CCP modules are equipped with a Special Event
Trigger. This is an internal hardware signal generated
in Compare mode to trigger actions by other modules.
The Special Event Trigger is enabled by selecting
the
(CCPxM<3:0> = 1011).
For either CCP module, the Special Event Trigger resets
the Timer register pair for whichever timer resource is
currently assigned as the module’s time base. This
allows the CCPRx registers to serve as a programmable
Period register for either timer.
The Special Event Trigger for CCP2 can also start an
A/D conversion. In order to do this, the A/D Converter
must already be enabled.
(Timer1/Timer3 Reset)
Special Event Trigger
Special Event Trigger
CCP1CON<3:0>
CCP2CON<3:0>
Compare
Output
Output
Logic
4
Logic
4
TIMER1/TIMER3 MODE SELECTION
SOFTWARE INTERRUPT MODE
SPECIAL EVENT TRIGGER
Special
S
R
S
R
Q
Q
© 2008 Microchip Technology Inc.
Output Enable
Output Enable
Event
TRIS
TRIS
Trigger
CCP1 pin
CCP2 pin
mode