C8051F061-GQR Silicon Laboratories Inc, C8051F061-GQR Datasheet - Page 296

• Manufacturer Part Number: C8051F061-GQR
• Description: IC 8051 MCU 64K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F061-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 24
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b, 8x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

C8051F060/1/2/3/4/5/6/7
24.2.2. Capture Mode
In Capture Mode, Timer 2, 3, and 4 will operate as a 16-bit counter/timer with capture facility. When the
Timer External Enable bit (found in the TMRnCN register) is set to ‘1’, a high-to-low transition on the TnEX
input pin causes the 16-bit value in the associated timer (THn, TLn) to be loaded into the capture registers
(RCAPnH, RCAPnL). If a capture is triggered in the counter/timer, the Timer External Flag (TMRnCN.6)
will be set to ‘1’ and an interrupt will occur if the interrupt is enabled. See
on page 151
As the 16-bit timer register increments and overflows TMRnH:TMRnL, the TFn Timer Overflow/Underflow
Flag (TMRnCN.7) is set to ‘1’ and an interrupt will occur if the interrupt is enabled. The timer can be config-
ured to count down by setting the Decrement Enable Bit (TMRnCF.0) to ‘1’. This will cause the timer to
decrement with every timer clock/count event and underflow when the timer transitions from 0x0000 to
0xFFFF. Just as in overflows, the Overflow/Underflow Flag (TFn) will be set to ‘1’, and an interrupt will
occur if enabled.
Counter/Timer with Capture mode is selected by setting the Capture/Reload Select bit CP/RLn
(TMRnCN.0) and the Timer 2, 3, and 4 Run Control bit TRn (TnCON.2) to logic 1. The Timer 2, 3, and 4
respective External Enable EXENn (TnCON.3) must also be set to logic 1 to enable a captures. If EXENn
is cleared, transitions on TnEX will be ignored.
296
External Clock
SYSCLK
(XTAL1)
Tn
TnEX
for further information concerning the configuration of interrupt sources.
Crossbar
8
2
12
Crossbar
EXENn
Figure 24.11. T2, 3, and 4 Capture Mode Block Diagram
TRn
0
1
TMRnCF
Capture
M
T
n
1
M
T
n
0
T
O
G
n
O
E
T
n
Rev. 1.2
TCLK
D
C
N
E
RCAPnL
TMRnL
0xFF
RCAPnH
TMRnH
0xFF
OVF
Toggle Logic
Section “13.3. Interrupt Handler”
CP/RLn
EXENn
EXFn
C/Tn
TRn
TFn
0
1
Interrupt
(Port Pin)
Tn