PIC17C42A-33I/PQ Microchip Technology, PIC17C42A-33I/PQ Datasheet - Page 83

• Manufacturer Part Number: PIC17C42A-33I/PQ
• Description: IC MCU OTP 2KX16 PWM 44-MQFP
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C42A-33I/PQ

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 33MHz
• Connectivity: UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: OTP
• Ram Size: 232 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-MQFP, 44-PQFP
• Processor Series: PIC17C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 232 B
• Interface Type: SCI, USART
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Operating Supply Voltage: 2.5 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• For Use With: AC164316 - MODULE SKT MPLAB PM3 44MQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

13.0
The USART module is a serial I/O module. The USART
can be configured as a full duplex asynchronous sys-
tem that can communicate with peripheral devices such
as CRT terminals and personal computers, or it can be
configured as a half duplex synchronous system that
can communicate with peripheral devices such as A/D
or D/A integrated circuits, Serial EEPROMs etc. The
USART can be configured in the following modes:
• Asynchronous (full duplex)
• Synchronous - Master (half duplex)
• Synchronous - Slave (half duplex)
FIGURE 13-1: TXSTA REGISTER (ADDRESS: 15h, BANK 0)
1996 Microchip Technology Inc.
bit7
bit 7:
bit 6:
bit 5:
bit 4:
bit 3-2: Unimplemented : Read as '0'
bit 1:
bit 0:
R/W - 0 R/W - 0 R/W - 0 R/W - 0
CSRC
UNIVERSAL SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (USART)
MODULE
CSRC : Clock Source Select bit
Synchronous mode:
1 = Master Mode (Clock generated internally from BRG)
0 = Slave mode (Clock from external source)
Asynchronous mode:
Don’t care
TX9 : 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
TXEN : Transmit Enable bit
1 = Transmit enabled
0 = Transmit disabled
SREN/CREN overrides TXEN in SYNC mode
SYNC : USART mode Select bit
(Synchronous/Asynchronous)
1 = Synchronous mode
0 = Asynchronous mode
TRMT : Transmit Shift Register (TSR) Empty bit
1 = TSR empty
0 = TSR full
TX9D : 9th bit of transmit data (can be used to calculated the parity in software)
TX9
TXEN
This document was created with FrameMaker 4 0 4
SYNC
U - 0
—
U - 0
—
The SPEN (RCSTA<7>) bit has to be set in order to
configure RA4 and RA5 as the Serial Communication
Interface.
The USART module will control the direction of the
RA4/RX/DT and RA5/TX/CK pins, depending on the
states of the USART configuration bits in the RCSTA
and TXSTA registers. The bits that control I/O direction
are:
• SPEN
• TXEN
• SREN
• CREN
• CSRC
The Transmit Status And Control Register is shown in
Figure 13-1, while the Receive Status And Control
Register is shown in Figure 13-2.
TRMT
R - 1
R/W - x
TX9D
bit0
R = Readable bit
W = Writable bit
-n = Value at POR reset
(x = unknown)
PIC17C4X
DS30412C-page 83