M37516F8HP Renesas Electronics America, M37516F8HP Datasheet - Page 34

• Manufacturer Part Number: M37516F8HP
• Description: IC 740 MCU FLASH 32K 48QFP
• Manufacturer: Renesas Electronics America
• Series: 740/38000r

Specifications of M37516F8HP

• Core Processor: 740
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SIO, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

[I
The I
cation format.
•Bits 0 to 2: Bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
transmitted. The I
after the number of count specified with these bits (ACK clock is
added to the number of count when ACK clock is selected by ACK
clock bit (bit 7 of address 002F
BC0 to BC2 are returned to “000
Also when a START condition is received, these bits become
“000
8 bits.
•Bit 3: I
This bit enables to use the multi-master I
this bit is set to “0,” the use disable status is provided, so that the
SDA and the SCL become high-impedance. When the bit is set to
“1,” use of the interface is enabled.
When ES0 = “0,” the following is performed.
• PIN = “1,” BB = “0” and AL = “0” are set (which are bits of the I
• Writing data to the I
•Bit 4: Data format selection bit (ALS)
This bit decides whether or not to recognize slave addresses.
When this bit is set to “0,” the addressing format is selected, so
that address data is recognized. When a match is found between a
slave address and address data as a result of comparison or when
a general call (refer to “I
transfer processing can be performed. When this bit is set to “1,”
the free data format is selected, so that slave addresses are not
recognized.
•Bit 5: Addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit
is set to “0,” the 7-bit addressing format is selected. In this case,
only the high-order 7 bits (slave address) of the I
ter (address 002C
bit is set to “1,” the 10-bit addressing format is selected, and all
the bits of the I
data.
•Bit 6: SDA/SCL pin selection bit
This bit selects the input/output pins of SCL and SDA of the multi-
master I
•Bit 7: I
This bit selects the input level of the SCL and SDA pins of the
multi-master I
7516 Group
Rev.1.01
status register at address 002D
abled.
2
C Control Register (S1D)] 002E
2
2
” and the address data is always transmitted and received in
C control register (address 002E
2
2
2
C interface enable bit (ES0)
C-BUS interface pin input level selection bit
C-BUS interface.
Jul 01, 2003
2
C-BUS interface.
2
C address register are compared with address
2
16
C interrupt request signal occurs immediately
) are compared with address data. When this
2
C data shift register (address 002B
2
C Status Register,” bit 1) is received,
page 32 of 89
2
16
16
”.
)) have been transferred, and
).
16
) controls data communi-
2
C-BUS interface. When
16
2
C address regis-
16
) is dis-
2
C
Fig. 30 SDA/SCL pin selection bit
Fig. 31 Structure of I
TISS TSEL
b7
M u l t i - m a s t e r
I C - B U S i n t e r f a c e
2
10 BIT
SAD
ALS ES0 BC2 BC1 BC0
S C L
S D A
2
C control register
T S E L
T S E L
T S E L
T S E L
b0
I
(S1D : address 002E
Bit counter (Number of
transmit/receive bits)
I
enable bit
Data format selection bit
Addressing format
selection bit
SDA/SCL pin selection bit
I
level selection bit
2
2
2
C control register
C-BUS interface
C-BUS interface pin input
b2 b1 b0
0
0
0
0
1
1
1
1
0 : Disabled
1 : Enabled
0 : Addressing format
1 : Free data format
0 : 7-bit addressing
1 : 10-bit addressing
0 : Connect to ports P2
1 : Connect to ports P2
0 : CMOS input
1 : SMBUS input
format
format
0
0
1
1
0
0
1
1
0 : 8
1 : 7
0 : 6
1 : 5
0 : 4
1 : 3
0 : 2
1 : 1
S C L
S C L
S D A
S D A
1
2
1
2
/ P 2
/ T x D / P 2
/ P 2
/ R x D / P 2
3
2
16
)
5
4
2
4
, P2
, P2
3
5