MCF5272CVM66 Freescale Semiconductor, MCF5272CVM66 Datasheet - Page 395

• Manufacturer Part Number: MCF5272CVM66
• Description: IC MPU 66MHZ COLDFIRE 196-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5272CVM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART, USB
• Peripherals: DMA, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (4K x 32)
• Program Memory Type: ROM
• Ram Size: 1K x 32
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 196-MAPBGA
• Cpu Speed: 66MHz
• Embedded Interface Type: UART, QSPI, USB, TDM
• Digital Ic Case Style: BGA
• No. Of Pins: 196
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

Chapter 17
General Purpose I/O Module
This chapter describes the operation and programming model of the three general-purpose I/O (GPIO)
ports on the MCF5272. It includes details about pin assignment, direction-control, and data registers.
17.1
The MCF5272 provides up to 48 general-purpose I/O signals. The GPIO signal multiplexing is shown in
Table
multifunction GPIO pins default to general purpose inputs and all multifunction pins that are not shared
with a GPIO pin default to high impedance. To avoid indeterminate read values and reduce power
consumption, internal pull-up resistors are active immediately upon reset, and remain active until the
corresponding port direction registers are programmed.
The general-purpose I/O signals are configured as three ports, each having up to 16 signals. These three
general-purpose I/O ports are shared with other signals as follows:
Control registers for each port select the function (GPIO or peripheral pin) assigned to each pin. Pins can
have as many as four functions including GPIO. There is no configuration register for GPIO port C
because its pins are configured by WSEL during device reset.
An additional port, port D, has only a control register which is used to configure the pins that are not
multiplexed with any GPIO signals.
Freescale Semiconductor
17-1. All GPIO pins are individually programmable as inputs or outputs. At reset, all configurable
PA[6:0]
PA7
PA[15:8]
PB[7:0]
PB[15:8]
PC[15:0]
GPIO Signal
Overview
MCF5272 ColdFire
External USB transceiver interface signals
QSPI_CS3 and DOUT3
PLIC TDM ports 0 and 1
UART1 signals and the bus control signal TA
Ethernet controller signals
Data bus signals D[15:0]. These are only available (as GPIO) when the device is
configured for 16-bit data bus mode using the WSEL signal
Table 17-1. GPIO Signal Multiplexing
®
Integrated Microprocessor User’s Manual, Rev. 3
Also Multiplexed on the Same Pins
17-1