XBIB-U Digi International/Maxstream, XBIB-U Datasheet - Page 26

• Manufacturer Part Number: XBIB-U
• Description: BOARD USB ZIGBEE MOD PRO
• Manufacturer: Digi International/Maxstream

Specifications of XBIB-U

• Design Resources: XBIB-U Shematic
• Accessory Type: Interface Board
• For Use With/related Products: XBee and XBee Pro Radios
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Special
Table 3‐01. XBee‐PRO Commands ‐ Special
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
Networking & Security
Table 3‐02. XBee/XBee‐PRO Commands ‐ Networking & Security (Sub‐categories designated within {brackets})
XBee/XBee‐PRO™ OEM RF Modules ‐ 802.15.4 ‐ v1.xAx [2007.05.031]
AT
Command
WR
RE
FR ( v1.x80*)
AT
Command
CH
ID
DH
DL
MY
SH
SL
RR ( v1.xA0*)
RN
MM ( v1.x80*)
3.2. Command Reference Tables
Command
Category
Special
Special
Special
Command
Category
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
XBee/XBee-PRO RF Modules expect numerical values in hexadecimal. Hexadecimal values are des-
ignated by a “0x” prefix. Decimal equivalents are designated by a “d” suffix. Commands are con-
tained within the following command categories (listed in the order that their tables appear):
All modules within a PAN should operate using the same firmware version.
Name and Description
Write. Write parameter values to non-volatile memory so that parameter modifications
persist through subsequent power-up or reset.
Note: Once WR is issued, no additional characters should be sent to the module until
after the response "OK\r" is received.
Restore Defaults. Restore module parameters to factory defaults.
Software Reset. Responds immediately with an OK then performs a hard reset
~100ms later.
Name and Description
Channel. Set/Read the channel number used for transmitting and receiving data
between RF modules (uses 802.15.4 protocol channel numbers).
PAN ID. Set/Read the PAN (Personal Area Network) ID.
Use 0xFFFF to broadcast messages to all PANs.
Destination Address High. Set/Read the upper 32 bits of the 64-bit destination
address. When combined with DL, it defines the destination address used for
transmission. To transmit using a 16-bit address, set DH parameter to zero and DL less
than 0xFFFF. 0x000000000000FFFF is the broadcast address for the PAN.
Destination Address Low. Set/Read the lower 32 bits of the 64-bit destination
address. When combined with DH, DL defines the destination address used for
transmission. To transmit using a 16-bit address, set DH parameter to zero and DL less
than 0xFFFF. 0x000000000000FFFF is the broadcast address for the PAN.
16-bit Source Address. Set/Read the RF module 16-bit source address. Set MY =
0xFFFF to disable reception of packets with 16-bit addresses. 64-bit source address
(serial number) and broadcast address (0x000000000000FFFF) is always enabled.
Serial Number High. Read high 32 bits of the RF module's unique IEEE 64-bit
address. 64-bit source address is always enabled.
Serial Number Low. Read low 32 bits of the RF module's unique IEEE 64-bit address.
64-bit source address is always enabled.
XBee Retries. Set/Read the maximum number of retries the module will execute in
addition to the 3 retries provided by the 802.15.4 MAC. For each XBee retry, the
802.15.4 MAC can execute up to 3 retries.
Random Delay Slots. Set/Read the minimum value of the back-off exponent in the
CSMA-CA algorithm that is used for collision avoidance. If RN = 0, collision avoidance
is disabled during the first iteration of the algorithm (802.15.4 - macMinBE).
MAC Mode. Set/Read MAC Mode value. MAC Mode enables/disables the use of a
MaxStream header in the 802.15.4 RF packet. When Mode 0 is enabled (MM=0),
duplicate packet detection is enabled as well as certain AT commands. Modes 1 and 2
are strict 802.15.4 modes.
© 2007 MaxStream, Inc.
• Special
• Networking & Security
• RF Interfacing
• Sleep (Low Power)
• Serial Interfacing
• I/O Settings
• Diagnostics
• AT Command Options
Chapter 3 ‐ RF Module Configuration
Parameter Range
-
-
-
Parameter Range
0x0B - 0x1A (XBee)
0x0C - 0x17 (XBee-PRO)
0 - 0xFFFF
0 - 0xFFFFFFFF
0 - 0xFFFFFFFF
0 - 0xFFFF
0 - 0xFFFFFFFF [read-only]
0 - 0xFFFFFFFF [read-only]
0 - 6
0 - 3 [exponent]
0 - 2
0 = MaxStream Mode
1 = 802.15.4 (no ACKs)
2 = 802.15.4 (with ACKs)
Default
-
-
-
Default
0x0C (12d)
0x3332
(13106d)
0
0
0
Factory-set
Factory-set
0
0
0
26